Jump to content
SAU Community

F.s. Autogage Monster Tacho (used)

S T A R 3 3

By S T A R 3 3,
in Australian Capital Territory

 Share

Recommended Posts

S T A R 3 3 Veteran

S T A R 3 3

Posted
Posted (edited)

EDIT: $50 for both.. YAY!

:wave:

I'm here in Lanyon (Banks) PM me.

Hey guys..

I'm selling my Auto Meter monster tacho and oil pressure guage.

The monster works. It was previously in my Celica, but I took it out once I rewired the original tacho in the dash working - sooo much better! There's not the spotlight that comes with it.

When I pulled out the tacho, it's wires were EVERYWHERE! They were chopped up, twisted to the originals and taped together. But I can assure you that it works.

As for the oil pressure guage (Auto Meter - Sport comp), it never worked. Mainly coz it wasn't connected.. coz it had no wires connecting to anything. I think the previous owner shoved mounted it up there on the pillar of the Celica for aesthetic value. But I'll throw it in there, and hope for the best.

I'm just doing some cleaning and found them on the floor. I want to get rid of them together because I'm tired of running around the house with them held up in front of me pretending I'm in a car.

First come, first serve!

PM me.

Freak456.jpg

Freak457.jpg

Edited by S T A R 3 3
Link to comment
https://www.sau.com.au/forums/topic/156707-fs-autogage-monster-tacho-used/
Share on other sites
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...