Jump to content
SAU Community

Recommended Posts

nice work mate, veryvery well done. i noticed your carbon canister lines have been 'chopped'. why don tyou have one of those? its the two lines that you have put the screws in...

Photo was taken when we chopped the paint tin size carbon canister out, I have since purchased a standard size carbon canister and put it back in.

So what was coated for the $210 ?

just plenum and piping? or the engine covers as well ?

plenum, intercooler piping, cam coveres, strut brace mounts, radiator mounts. I chose 2 different colours (the silver and dark blue) which made it more expensive (Min charge of $50 per new colour). If you want all the one colour it will prob. be a bit cheaper. Powdercoating is very cheap if you go to the right place.

I am not that happy with the colours, the cam covers turned out a lot bluer than I wanted, I was after a gun metal grey look but had to re-choose the colours I had chosen because I chose the only range that they did not have in stock.

Forgot to add that the pearl flakes etc cost a little bit extra with the powdercoating.

  • 2 years later...

Ah yeh woops sorry. I see the braided lines now. I think I might have been looking at a different pic.... possibly this one: http://www.skylinesaustralia.com/forums/Pu...80&start=80

But yeah, my question still stands... regarding the tube from radiator-to-coolant bottle and the tubes which "look-like" they are attached to his power steering fluid reservoir.

The only reason i sound like a broken record asking the same stuff over and over again...is because i've been getting mixed answers from a few people (I'm a total amateur when it comes to stuff under the hood). So sorry for that.

I did notice a weird thing though... I replaced one hose which was for air/vaccum (it was previously disconnected anyway, it had worn out and broken off from where it was attached) and my Boost guage needle started flickering? previously it had just been lying still at the bottom when the car was turned on. Not sure if this is normal.

to help you out a little..

i have used a cheap rubber "dress up" hose from my radiator tro overflow bottle for a long time and also for my breather pipes.. its had no dramas. its not silicon and is very flimsy but has held up for a few years now.

proper silicon hoses can be used for coolant lines to a bleed bottle etc.. aslong as they are clamped good. they are usually 3mm thick and being silicon they are very heat resistent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...