Jump to content
SAU Community

Recommended Posts

I am looking at buying an R33 GTS-T from interstate.

What do i need to do if i want to register it here in SA? Does it matter if it comes with RWC or not?

Description-

130,000kms, 1994 model, genuine car, Rare Factory Black, 5sp manual with Electric Sunroof, Grade 3.5 Auction with NO accident histrory. Straight vehicle with good modifications, incl coilover supension, Blitz Adjustable Boost Controller, updated rear spoiler, Apexi N1 exhaust, Apexi Super AFC and Air intake, factory sunroof, runs very well, incl full compliance and RWC.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/161843-buying-r33-gts-t-from-interstate/
Share on other sites

RWC doesnt apply in South Australia..As far as Im aware of. Also as far as buying it interstate. When you bring the car into SA all you need to do is get the VIN number checked at regency or if your more than 50kms from there, a local cop shop and then you simply change over rego...Just try make sure the acar isnt moddded to much when going through regency or you will probably end up with a defect as well.

Good luck..

Beki :unsure:

Be sure your living 40km's out of the CBD so you can take it to the local cop shop for its identity check.

Otherwise its a regency job where they give it a brief looking over. :unsure:

So I was told when recently enquiring about the purchase of an interstate vehicle.

OR, you can get the owner to write a statement saying you have been living with them interstate for 3+ months, take it to a rego department over there, register the car in your name and then drive it back here. Then, all you need to do is fill in a form to transfer rego, no checks, nothing, simple :unsure:

Hi

I just recently bought a skyline from interstate exact same type as yours actually (black with sunroof) and you shouldnt have any probs getting it registered here, just make sure when your getting your vehicle id inspection done your car is pretty stockish looking cause i took mine to Sturt Cop shop and they had a full hard look over it. Other than that just make sure if you have tinting on car that its legal cause there really picky about that.

Edited by /2on

Hey,

Ive brought two R33's from interstate. Both through regency. No matter what they will do a VIN check ( was registered in my name in NSW ). First one was stock, just had an exhaust. Had no worries. Second one I bought in had tinted windows, exhaust, 18s stock air box. They wouldnt register it until i removed the window tinting. They are really big on window tinting and test every car, you won't get through with it on. Its not the same workshop that you would goto if you got defected. I found some of the employees there particularly unfriendly. Guess they have a shit job really. Its also rumoured that they check the passenger kick panel for aftermarket ECUs. If you can, make the car as standard and clean as possible when you go though, you will be fine.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...