Jump to content
SAU Community

Recommended Posts

hey,

Finally my car is making some progress. After the gearbox dilema, i have got most of the stuff sorted. And a big spending spree planned to buy and get all work done this week. pump, tailshaft, radiator, thermos.

Next weekend with everything in and ready to go, except the exhaust, is it ok to drive it around straight off the dump pipe?

I dont have a front pipe to connect to the rest of the exhaust.

And the engine mounts are going to be modded where i am getting the cooler piping, and new dump/front made up, so i will have to go with no bonnet either. And just run the stock cooler to the place. (its through back streets so i guess it should be ok, for no cops to pull me over.

But the place i got to take the car to is like 10 minutes away, anyway, and getting it towed is just not worth it. Seeing as i can drive it anyways.

But yeah, driving off the dump pipe that doesn't harm anything does it?

just freakn noisey yeah.

i am getting worries about the big i will cop if i do get busted. so i might just bolt up half a vl exhaust with a cat.

and run the standard silvia exhaust, so it still looks like i got a zorst. although i will be taking it round the block, just because.

got to find some stock cooler piping now.

so i can do so.

damn it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...