Jump to content
SAU Community

Recommended Posts

can i ask what for?

Anything that is engineered will probably be refused anyway. Regency and police are exempt from the law if they think anything goes against ADR laws -in their mind- then it is defectable and will not be allowed on the road. This is with a certificate and engineered product as well.

I know a friend spent over 2k getting suspension engineered that would pass aus wide ADR laws, and it was knocked back.

You're better off not even trying in SA. Its the law, and it sucks.

Edited by Bl4cK32
Link to comment
https://www.sau.com.au/forums/topic/163482-good-engineer/#findComment-3033768
Share on other sites

The only way I've found to get around emissions (well told by some one in vehicle standards) here in SA is to move to NSW. Get the car emissions tested and engineer signed off that it meets ADR's, get it all reg'd then move back here and transfer the rego.

Live 40km's away from the CBD so you are allowed to have a simple VIS check done by the local cop shop, be sure to bring all the associated documents from the modifications/engineer/emissions etc.

Live inside of the 40km's and you'll be off to regency for a vis + roadworth that often than not they pick up something.

Then the car will probably be defected and regency won't honor nsw's emissions testing engineering adr etc..

Who knows, they don't LMAO!

There is word that SA is in the process of sorting out emissions testing for petrol vehicles, I'm not going to hold my breath.

Link to comment
https://www.sau.com.au/forums/topic/163482-good-engineer/#findComment-3033772
Share on other sites

I havent done anythink yet but was planning on getting 20ich rims with coilovers and c/f bonnet, i wanted to do it the right way but now thinking i might just have to stick with 18's and risk the c/f bonnet. The reason i wanted to get engineered was that im spanding so much on this car and wanted to do it right.

ADELAIDE needs a mod plate

Link to comment
https://www.sau.com.au/forums/topic/163482-good-engineer/#findComment-3033791
Share on other sites

cf illegal due to the way it reacts during a crash. If u paint it u lose the wank factor of having one to start with. Its been covered here before.

Coilovers are illegal unless u weld them @ std height. No point having them as well, see SK's definition of why (unsuited to australian roads etc etc...)

Link to comment
https://www.sau.com.au/forums/topic/163482-good-engineer/#findComment-3033983
Share on other sites

I am an engineer and 95% of the posts in this thread are absolute crap............. You can do anything you want with a car as long as the maths supports your theory,............

Unfortunately it cost$$.. I will do some approvals for free, but extremem shiat will take some brain hurtin g...

Let me know if youj want the good oil... And dont just take what the RTA DMR QTA says is gospel............

ENgineering wasnt cool when we were 15, but its really cool when you running 400rwkw's and the boys cant touch you..

Insert evil laugh.....Muhamuhamuham

PM me for my number dude,... We are just about to import another car that is going to be insane HPO, and drivable...

S

Link to comment
https://www.sau.com.au/forums/topic/163482-good-engineer/#findComment-3035512
Share on other sites

I am an engineer and 95% of the posts in this thread are absolute crap............. You can do anything you want with a car as long as the maths supports your theory,............

Nice way to say hi :)

Can u then stand by your certificates saying that the police will not defect the car still, requiring a trip to regency to clear? Given the fact they only have to have a suspicion of a defect -without knowledge of the ADR laws that they are defecting for?

Are u saying that even though regency engineers can knock back certified safe cars that u will stand by your certifications, and take them to court to follow the matter up, even though they are expemt from any decisions made by them?

Please elaborate because i know a few hundered people here and on other foums would love to see you and your certs/plates get past the system that has raped many...

Link to comment
https://www.sau.com.au/forums/topic/163482-good-engineer/#findComment-3035793
Share on other sites

It either complies with state and federal legislation or it doesnt..

It is very black and white.... You will find it hard to find anyone that will write dodgy approvals..

But if it is a pass, it is a pass.. Simple..

U know that, we all know that. Explain why regency wont agree with it. Fact - people who have engineers certified mods on their cars in SA have been defected in the past.

Even if u have a mod plate and all mods comply regency can still refuse it on the road, which HAS happened.

Even if u STILL get it past them, there is nothing to stop police sending u back again.

Its all good to state it will pass if its legal, but we all know regency doesnt care, the police dont. It a revenue raising bitch, and u cant do shit except chase your tail.

Have a look at the law and theres a loop hole that states regency doesnt have to explain what they do. Dont make me dig it out. :P

Its all good to offer a cert plate, but in the end u will still end up back at regency.

So please offer an explanation as to why u think your certification would be different to anyone else, and if you would challenge regency as to why it was knocked back.

Link to comment
https://www.sau.com.au/forums/topic/163482-good-engineer/#findComment-3036552
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah its a server spammer thing  Although, now that I manually approve all the accounts I can probably loosen up some of the restrictions.  
    • Thread bump, again! Although, no bad news this time. Posting for the sake of possible root cause. Basically, I rebuilt it (mostly stock), installed Haltech + sensors, had it running fine on new ECU.  Still not really understanding why it cracked pistons last time. Got to tuners, and while checking timing, noticed +-10deg of timing scatter while revving. Changed CAS, and it was rock solid. While not definitive, can't imagine seeing 20+ psi with that amount of scatter would be a good thing. Also glad I found something.   Bit more of a run down; Carried out a stock rebuild, a set of stock pistons, out of a spare bottom end. Everything stock apart from head studs and oil restrictors. (so I can pretend I didn't let the Nissan out, ha.) Armed with the measuring gear and FSM, set about doing overhaul. Oil restrictors as per oil control thread for a RB25, stock oil pump, drifting. Head drain/vent from rear of head, to passenger side of sump above oil level. Two dash 10 vent lines from drivers side of sump (unused atm) Hi octane style cam cover breather kit Splash covers over last 2 cam caps. Both breather lines from cam covers to vented to atmosphere catch can, not plumbed back into sump (wanted to see what it was actually breathing). Got it run in (did about a 1000km) no to low boost scenario, As I had questions over old ECU setup. Installed haltech +sensors for flex Retune on E85 (finding CAS Issue along the way), made 300rwkw at 20psi, out of wastegate. Did a drift day the next day (yes, it was a big weekend!) and was checking catch can throughout the day, ZERO blowby. I mean nothing. Lines from cam covers are not even wet. Done a bunch of street driving, spirited and catch can is still dry. Early days I guess, but pretty happy so far. Also now run 10w60, up from the 10w40 that I used to run. Oil pressure is significantly better, especially when hot (as you would expect)      
    • Thanks buddy. I thought it was a server storage thing. 🤣
    • Perfect! Thanks for this, both look like great options!
×
×
  • Create New...