Jump to content
SAU Community

Recommended Posts

ok i have searched far and wide and i cannot get anything!!!! 4 different forums and many traders haha.... apparently they make no more for rb20! soooo what can i use as a replacement?? please help and i dont wanna remap my comp everytime i modify!

cheers

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/
Share on other sites

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

I'm still a big PFC fan... The knock dash light flash is awesome, confidence inspiring especially as dyno's have a nasty habit of not placing enough load on the motor during tuning, once u get it on the street and load it up in that 4th gear from low rpm it pings its arse off. :w00t:

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/#findComment-3037681
Share on other sites

A lot of tuners have a bad taste in their mouth when they hear the word Greedy Emanage.

As a result some will steer you away from it.

As with everything.. Some tuners deal microtech, some autronic, some microtech + powerfc. Use the ecu your tuner feels the most comfortable with as you WILL receive the best tune doing so.

Paul.. 440 is for a full tune.

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/#findComment-3040951
Share on other sites

i dont get it, why the bad taste. is it because no ones had experience with it or bothered using it?

Cubes can you provide a few good reasons why Greddy Emanage isnt used apart from tuners being lazy?

Thanks.

A bad taste is where in the products history it has performed Poorly. Hence the bad taste left over from the older greedy emanage version.

Apparently the Emanage Ultimate is better. But the damage has been done. Its left a bad taste.

Absolutely nothing to do with slackness.

URAS has good results with them. Get him to tune it.

Go to some one who doesn't know its in's and outs and you are likely to not get a nice tune without spending big $$ for dyno time and fiddling around. Quite obvious really.

Now that the PFC is out of the picture it may very well take off, the tuners will be forced to spend some time on the greedy as they become more common.

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/#findComment-3042238
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...