Jump to content
SAU Community

Recommended Posts

ok i have searched far and wide and i cannot get anything!!!! 4 different forums and many traders haha.... apparently they make no more for rb20! soooo what can i use as a replacement?? please help and i dont wanna remap my comp everytime i modify!

cheers

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/
Share on other sites

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

I'm still a big PFC fan... The knock dash light flash is awesome, confidence inspiring especially as dyno's have a nasty habit of not placing enough load on the motor during tuning, once u get it on the street and load it up in that 4th gear from low rpm it pings its arse off. :w00t:

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/#findComment-3037681
Share on other sites

A lot of tuners have a bad taste in their mouth when they hear the word Greedy Emanage.

As a result some will steer you away from it.

As with everything.. Some tuners deal microtech, some autronic, some microtech + powerfc. Use the ecu your tuner feels the most comfortable with as you WILL receive the best tune doing so.

Paul.. 440 is for a full tune.

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/#findComment-3040951
Share on other sites

i dont get it, why the bad taste. is it because no ones had experience with it or bothered using it?

Cubes can you provide a few good reasons why Greddy Emanage isnt used apart from tuners being lazy?

Thanks.

A bad taste is where in the products history it has performed Poorly. Hence the bad taste left over from the older greedy emanage version.

Apparently the Emanage Ultimate is better. But the damage has been done. Its left a bad taste.

Absolutely nothing to do with slackness.

URAS has good results with them. Get him to tune it.

Go to some one who doesn't know its in's and outs and you are likely to not get a nice tune without spending big $$ for dyno time and fiddling around. Quite obvious really.

Now that the PFC is out of the picture it may very well take off, the tuners will be forced to spend some time on the greedy as they become more common.

Link to comment
https://www.sau.com.au/forums/topic/163810-pfc/#findComment-3042238
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...