Jump to content
SAU Community

Yokohama Semi Slicks Ao48's

ZX2NV
 Share

Recommended Posts

ZX2NV Contributor

ZX2NV

Posted
Posted

I have up for grabs 4 yokohama AO48 semi slick race tyres

http://www.yokohama.com.au/motorsports/

Sizes are 2 x 265 35 18 and 2 x 285 30 18

Tyres are in good overall nick no flat spots etc and with around 50% tread remaining. Tread depth averages around 3mm to the indicators and new they have close to 6mm. I have just upgraded to new R888's for the state supersprint series and circuit battle etc so the olds must go

Inspection is welcome prior to commitment

These are advertised on other forums etc aswell so get in quick if keen.

RRP for the set is well over 2k asking $225 per tyre or $800 for the set.

PM or email me at [email protected] or call 0401 466 661

Will have some actual product pics up later this week when the new tyres are fitted to my rims

Here is a pic on the rim. Note rims do not come with tyres 4 tyres only available

yokoa048sbz2.jpg

Cheers

Jason Edgley

ZX2NV

Link to comment
https://www.sau.com.au/forums/topic/165895-yokohama-semi-slicks-ao48s/
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...