Jump to content
SAU Community

Recommended Posts

Hi Peoples as the title says ceffy for sale

1988 Nissan Cefiro

1997 Series 2 RB25 Det

Rb25 Det Gearbox

Nismo Coppermix clutch

Tdo5h-18G Rebuilt with Tdo6 internals

FMIC Kit 600x300x76

GTR Radiator

R33 Steering Rack

Adj Caster Rods

R32 GTR Front Brakes

R33 Rear Brakes

M's Spec coilovers

TSP Bodykit (needs tlc)

Cusco Front and rear Strut braces

HKS EVC Boost Controller

Bosch 040 Fuel Pump

Remapped Standard ECU

Engineered Hicas Lock Bar

Engineered Intrusion Bars

Child restraints done

All ready to be complied :(

All papers (import approval etc) come with car

Shown without kit as i took it off for regency reasons

Lookin for 8500 or near offer Im located in Middleton SA which is 80kms south of adelaide

SMS ONLY 0419847512 or PM me on here

post-3988-1177558527.jpg

post-3988-1177558544.jpg

post-3988-1177558581.jpg

post-3988-1177558595.jpg

post-3988-1177558611.jpg

post-3988-1177558705.jpg

post-3988-1177558721.jpg

post-3988-1177558823.jpg

post-3988-1177558836.jpg

post-3988-1177558884.jpg

Edited by etbenno
Link to comment
https://www.sau.com.au/forums/topic/166126-rb25det-nissan-ceffy-for-sale/
Share on other sites

Nah no swaps need the money :) comes with r32 rims on the back and some fat black vip lookin rimmies on the front :) wont pass regency with that turbs unless u get it engineered which is $1000 to have done

Nah no swaps need the money :P comes with r32 rims on the back and some fat black vip lookin rimmies on the front :P wont pass regency with that turbs unless u get it engineered which is $1000 to have done

Hey man,

sent you a PM the other day with a couple of quick q's... can you fill me in on details?

Cheers,

Dave.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...