Jump to content
SAU Community

Recommended Posts

:domokun: so i was going down a road in the far left lane merging into the middle lane this morning during the rain and some arsehole in a 94 surburu liberty doesnt look and changes into the middle lane from the right and cuts me of, had to slamm on the ancors i lost control and slammed threw a sign and far bit of front end damage to panels and slight chassie bend, my motor and interia suspention n everything is perfect

so im looking for a shell to buy to swap everything over, what have you got??? looking either any skyline 32-34, 180sx/oilvia/sileighty or s15

Link to comment
https://www.sau.com.au/forums/topic/166535-i-need-a-shell/
Share on other sites

i have a R33 GTST rolling shell id like to off load im asking $2500 for it its missing the running gear preety much ! pm me if your intersetd or i have also S13 silvia rolling body shell and also s13/180 sx also im in melb

Link to comment
https://www.sau.com.au/forums/topic/166535-i-need-a-shell/#findComment-3083517
Share on other sites

for the shell im looking at 1500-2500 ish, the shel wont need any front panels as ill prob go aftermarket fenders front bar and bonnet, and wouldnt need rims or struts, interia is optional too but would need at least a dash pad if its not an r33, kinda leaning towards a 180sx so i can do a strawberry face conversion on it would look hot

i might re-valuate my budget if its not possible but one wreckers in wa was advertising shells for 2000, i live in melb so if interstate i would need to orginise freight into the budget to

Link to comment
https://www.sau.com.au/forums/topic/166535-i-need-a-shell/#findComment-3085978
Share on other sites

I have a r32 shell thats painted matt black

its got a few odds and ends like kframe and rear 5 stud,alloy subframe bushes,whiteline rear swaybar mounts and bushes,rear bootlid and can throw some other things in for 1500 but doesnt have any numbers or compliance on it

but perfect for what ur after

it has damage to rear right qtr panal but slightly repaired

Link to comment
https://www.sau.com.au/forums/topic/166535-i-need-a-shell/#findComment-3086188
Share on other sites

i need the shell to be complied as i will be engineering all the work and registering it on the roads and i cannot complie it with an engine other than standard, if it were complied i would defonatly be interested thou

Link to comment
https://www.sau.com.au/forums/topic/166535-i-need-a-shell/#findComment-3086224
Share on other sites

hey i might very well be interested, when you mean no front do you mean no front bar no fenders or do you mean no front bulkhead? has it been complienced? has it been written off? where abouts are you?

im in melb give me a buzz on 0401011380 or a pm

cheers jarrod

i have one no doors or front its rolling asking $2000 pm me if this is what you are after
Link to comment
https://www.sau.com.au/forums/topic/166535-i-need-a-shell/#findComment-3099774
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...