Jump to content
SAU Community

Recommended Posts

hahe i love it, thats awesome. As it would be nice to be able to have it lower the flow, and not heat the fuel so much when idling through traffic.

Course... as long as it never accidentally doesn't flick over, and you hit max boost at 7k rpm with low volts and half fuel flow... :P

that could be ugly, it would go from 13.8v from the relay to 10.5v from the modulator im gonna have a led next to the boost guage to monitor when its on, its got separate adjustable cut in cut out so it can turn on above 8psi and off below 2 psi to make it stable.

  • Replies 98
  • Created
  • Last Reply

Top Posters In This Topic

HOW GOOD!!!

I want.. how do you hook this up to my car? i use AFM ?

ok so it probly is hot fuel you could measure the return temp to prove it.

I ran 8g from the battery to a distro block in the boot because the stock wiring was only supplying 10.5v to the pump so now it gets 13.8v at the pump.

The gtr pumps 270 litres per hour at 14volts and will maintain flow up to 30 psi boost [according to tests done in the uk with a few different pumps]

So its no slouch but in a stock gtr it only gets 10.5 volts max and 5.5v at idle/ low demand, the manual says its to save power but i think the heated fuel in traffic had a part to play in too and 10.5 v is ok at stock boost

I got an adjustable voltage sensing relay from jaycar to connect to the map sensor for the sub meter boost gauge that will switch in a relay on the earth side of the pump at high boost but still allow the modulator to control the pump speed at idle/low loads and keep the fuel cool.

oh some more testing done today. drove from the central coast to the end of the freeway and the noise started (tank was close to empty) before i got to the servo it was getting noisy again... put $40 in and then it went back to normal sound and normal a/f ratio's and did not make any noise all the way to work.

So its definatly fuel temp issues.... I am convinced.

Guilt Toy..

There's definitely something up as on a day like this myself and mates definitely don't have fuel temp/noise issues even when running on empty *red light on*.

Our pumps only start making noise on warmish 30degree+ days.

Have you tried pointing the return away from the pumps pickup? Maybe your aerating the fuel some what which shows up when low on fuel?

I am using the stock setup. using the walbro pump to pickup fuel and feed to the 044 then the 044 push's to the front of the car.

I have not changed the pickup or returns at all - its all stock

Guilt Toy..

There's definitely something up as on a day like this myself and mates definitely don't have fuel temp/noise issues even when running on empty *red light on*.

Our pumps only start making noise on warmish 30degree+ days.

Have you tried pointing the return away from the pumps pickup? Maybe your aerating the fuel some what which shows up when low on fuel?

I rang John and he has a stock z32 oil cooler runnong on the return line at the rear of his car in the wheel arch with an air duct.

I am going to run one on the return line at the front of the car. Cool the fuel going back to the tank... would think it would be better to run it on the way to the engine as i can see it giving a better burn that way but its under pressure there....

have you taken it to sydney traffic ? sometimes you can be at stop start traffic and not going above 30 km's an hour for 30 minutes at a time... I dont have issues when i am boosting around the streets at home its just in very heavy traffic.

Guilt Toy..

There's definitely something up as on a day like this myself and mates definitely don't have fuel temp/noise issues even when running on empty *red light on*.

Our pumps only start making noise on warmish 30degree+ days.

Have you tried pointing the return away from the pumps pickup? Maybe your aerating the fuel some what which shows up when low on fuel?

have you taken it to sydney traffic ? sometimes you can be at stop start traffic and not going above 30 km's an hour for 30 minutes at a time... I dont have issues when i am boosting around the streets at home its just in very heavy traffic.

I have the same setup, intake lift with the external. Regardless if its an empty tank or full take I still get the noisy pump when the amb temp is warm, empty tank noisy fuel pump then fill up, its quiet for 5mins or so then gets noisy again.

We have a little stretch heading home where you sit jammed in traffic for a good 30mins and you literally move a couple of car positions then sit for another 5mins, this repeats for a good 30mins; the only difference being your lucky to even register a speed on your speedo. I would say its comparable.

Pointing the return away from the pick up is a suggestion that others have said they have had good results with in reducing the noise of the pump on those warm days.

Its only a suggestion that may save you a couple hundred. :S

well i can only bring it down to fuel temp. when it makes noise the fuel pump is pretty warm.. this morning after i put half a tank of fuel in the car there was no noises and the pump was cool.

What else could it possibly be ?

sounding more like fuel temp problems, like i said mine does exactly the same. Only thing i don't get is why other people are not having the same problem. Every man and his dog with a skyline has upgraded the fuel pump but only a handful are suffering these problems.

Is it possible we are "over Fuelling" for our power levels. i'm only making 350hp at the wheels at the moment. perhaps i'm pushing to much fuel to the engine bay and just not consuming enough and thus with the large amount of fuel returning to the tank the fuel in the tank just gets to hot.

anyways good luck with the fuel cooler.

I was told to put it on the return line... but i would love to be able to put it on the other side for performance gains ;) not that it will make much difference

Yes this is correct - use the return line as the pressure is much less. You'll be surprized how effective this is, I run a small Perma-cool power steer cooler on my return line (at the front) and the surge tank is way cooler, no more fuel heating issues for me.

Id say it is heat related, maybe the fuel when hotter, cavitates more easily into the pump.

I would say both making the fuel cooler or changing the angle of the return line would work.

Seems strange some people get the issue and some don't. I would have to say, it must be due to small differences in installation angle, depth, running original sock filter etc etc.

HOW GOOD!!!

I want.. how do you hook this up to my car? i use AFM ?

you can use a gtr boost guage sensor, beer baron had a couple of gtr boost sensors for sale a while ago

you could go back to the stock setup [dropping resistor and relay] and wire another one in parrallel for the 044 except connect the negative to your wire direct from the battery

i dont know when the ecu decides to go to high flow, probly airflow or throttle position or both.

Just thought I'd chime in. I have had the same exact problems with the 044 pumps on my Porsches. After lots of trial, error, browsing the internet, etc I finally determined what was causing the fluctuating whining is heat related. I'm not saying this is necessarily the problem for everyone experiencing similar issues with these pumps. Both of my current Porsches have external pumps, and they are mounted in areas that receive poor cooling and limited airflow. I have noticed with mine that, sometimes they will be relatively quiet and consistant, but usually they start to whine a bit louder and sometimes in a fluctuating manner after I have been driving either car for an hour or 2 and especially in slow/heavy traffic. Voltage fluctuations to the fuel pump are another possibility as well.

Okay i did more testing... and i am 100% sure that its fuel temp issues because yesterday arvo the pump was making very loud noises so i pulled into the servo (had low fuel) left the engine running and poped the boot so i could hear the pump and put in 40 litres of petrol.. as soon as i got up to around 15 litres of petrol the noise completly went away and it sounded normal.

So the extra fuel cooled down the system and i could even feel a temp difference when touching the pump.

i am going to try find a decent oil cooler and put it onto the system this weekend and see how it goes next week.

Guilt-Toy...

So is it the noise your worried about or the afr's going to shit when the fuel pump gets noisy?

Exactly what drivability issues do you experience? Light throttle surge? Idle lean missfire?

As I mentioned earlier (i think) :) I have been experiencing a few light throttle surge and idle lean missfires. BUT it occurs randomly; most of the time with the fuel pump noisy but also a lot of the time when its quiet. Putting fuel in does make my fuel pump quiet as yours did BUT it doesn't make a difference if the afr's are playing up on light throttle/idle. Does yours?

the car was idleing on 17 to 18 afr and when the pump cooled down it went down to around 15.5 (which is still leaner then normal) and it was still missing a little on idle....

on cruise when the pump is noisy it does surge alot and runs pretty lean.. my tune atm is set to around 14.5 - 15.5 on cruise when the pump gets noisy it goes up to 17 +

oh and im worried about both issues because one the noise annoys the shit out of me and 2 the car drives kinda rough when it leans out that much and its annoying too.

Boost is still normal afr's

I have a wideband afr meter in my car at all times now and thats what ive noticed.

Guilt-Toy...

So is it the noise your worried about or the afr's going to shit when the fuel pump gets noisy?

Exactly what drivability issues do you experience? Light throttle surge? Idle lean missfire?

As I mentioned earlier (i think) :) I have been experiencing a few light throttle surge and idle lean missfires. BUT it occurs randomly; most of the time with the fuel pump noisy but also a lot of the time when its quiet. Putting fuel in does make my fuel pump quiet as yours did BUT it doesn't make a difference if the afr's are playing up on light throttle/idle. Does yours?

Edited by Guilt-Toy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...