Jump to content
SAU Community

Recommended Posts

Just thought i'd post up a picture of my 1984 300c. I'm pretty happy with it so far (had it for 8 months) - and i've only seen 2 -3 others around Melbourne during that time. It runs the vg30e motor with a 4 speed auto. Gets up to 100 around the 10 sec mark, and handles really well too.

Might do some sort of engine conversion later on, or just lower it slightly and give it a fresh paint job.

post-10908-1179063359_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/168552-my-300c/
Share on other sites

Hi there,

Nice looking car. Seems to have been looked after very well. I'm sure I'll see you around the traps. Be sure to wave and say hi!

yeah i bought it of a dealer my friend knew who said it was traded in by some old bloke, so i got a pretty good price as they probably took it off his hands for next to nothing :rofl:

Link to comment
https://www.sau.com.au/forums/topic/168552-my-300c/#findComment-3115634
Share on other sites

  • 3 weeks later...
  • 2 months later...
  • 5 weeks later...

Well the car isnt at my house at the moment, partly because there is no space and partly to prevent me driving it :wave: but maybe this summer come around and we'll compare

I'm actually trying to source a motor for it at the moment, as the timing belt pulley bearing broke and i got a new pulley and belt put on it but its had a miss in it since- im thinking maybe a bent valve somewhere..

i got a quote at 660 but that particular wreckers didnt have any in stock. i might ring the one in centre road, see how many kms are on the one u mentioned..

Link to comment
https://www.sau.com.au/forums/topic/168552-my-300c/#findComment-3363510
Share on other sites

  • 2 weeks later...
  • 1 month later...

I cant fit spacers, otherwise it starts rubbing the inner guard in the rear. It's pretty tight in there due to it's height. The fronts I'm running 5mm spacers to clear the struts. If I go any bigger, I wont be able to steer the bloody thing!

Link to comment
https://www.sau.com.au/forums/topic/168552-my-300c/#findComment-3500936
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...