Jump to content
SAU Community

Misc Parts From R32 Half Cut And Odd Pieces... Pm Me What U Need


Recommended Posts

How you doing sau.

well ive got some lefted over pieces from my conversions.

LOCAL PICK UP PREFERED due to weight of most items.

Will trade anything for set of rims eg standard R32 R33 R34 rims or other parts..?

1 R32 GTST half cut (120,000kms), everything lefted part from slave cylinder, motor, box, loom, crossmember. the rest is left.

-good condition camber arms

-brakes 6xR32 front calipers 2x rears

-front hubs

-Power steering bits.

-hicas bits

- front light harness

-dash (NO BUBBLES NO CUTS, better condition dash than my GTR's :pwned: )

-all air vents LH SOLD

-digital climate control unit

-full a/c system, working condenser, pump, actuator etc. all lines too.

-door hinges

-GT badges (red)

-intercooler and most pipping

-glove box

-speedo drive cable SOLD

-brake lines

-brake master and clutch master

-pedals + brakets.

NO RUST IN FRONT OF SHELL.. good for someone who had a head on.

pm me what you need. ill take $800 for the whole thing.

$220 - R34 GTT intercooler and pipping (50,000kms)

ill install the R34 Gtt intercooler onto a R33 GTST for an extra $30 - good for RB25 upto 225kwATW with limited lag.. good upgrade for R33

$200 - R34 GTT airbox (40,000kms) new panel filter comes with snorkel

$50 - damaged alluminum R32 GTR bonnet.. was damaged coming off truck by crane see pic in last post.. bend in front and scratches.. comes with bonnet pin pins. SOLD

$25each - boost solenoids, BNR32, ECR33, ECR34, 200sx..

$15 each silicone hose 3 ply, 3"-2.5" , 2.5" blue, have standard hoses too.

$10 - exhaust heat shields,

from $20 each - GENUINE skyline + Nissan Floormats.. RRP $150-250 at nissan lol..

$30 - CA18 radiator

$50 - CA18 a/c units all working well..

$125 - CA18 digital + analog climate control

have more parts but thats all i can think of off the top of my head.

PM me with your offers and ill probably take them

thanks

mark.

NOTE** AIR VENTS IN GOOD WORKING ORDER. passenger airvent has crack on top right which has been repair not visible but works fine. centre is umarked and works fine.. (will be going on my GTR unless someone offers me something decent :dry: see pics.

post-25555-1179289340_thumb.jpg

post-25555-1179289402_thumb.jpg

post-25555-1179289459_thumb.jpg

post-25555-1179368929_thumb.jpg

post-25555-1179369002_thumb.jpg

Edited by markimak
  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

pic of R32 GTST cooler and R34 GTT cooler side by side.. look up to see my exceddy clutch box :pwned:

oh also got standard R32 GTST clutch plate, pressure plate ill take $10 for that.?

you can have the R34 GTT cooler installed for $220 exhanged.? or $250 drive in drive out. (approx 20mins)

post-25555-1179289949_thumb.jpg

Edited by markimak

Few more pics, floor mats are genuine SKyline and nissan items with SKyline badging on them.. off my BNR32 GTR still using 2 other front ones but will let the skyline floor mats go for the right price.

pics of R32 GTST rad over flow

Rad fan shrowd

Rad fan (viscous hub) CA18 and RB20

RB20 brake master and clutch master.

$offersCA18 ignitor

$25 - CA18 fuel pump suited to be a feeder pump for a larger fuel system

$15 - ok condition RB20 water pump worked well just replaced cause doing a tbelt.

CA18 + R34 GTT washer bottle

R34 GTT splash tray good condition

R34 GTT Neo cover

S13 lowered springs

S13 struts front and rear

S13 Struts front and rear kyob with cut king springs

space saver from R34 GTT new

Blitz silencer insert for exhaust off jasma muffler

R34 GTT spark plug cover

R34 GTT coil packs, they break down sometimes..?

R32 RB20DET Auto Tailshaft. was supplied an auto shaft with my manual half cut..?

PM me offers. i have charcoal canisters and other stuff that i cant think of.. pm me offers

of course item will go to highest offer at the time.. so best in best dressed..

post-25555-1179291563_thumb.jpg

post-25555-1179291629_thumb.jpg

post-25555-1179291693_thumb.jpg

post-25555-1179291779_thumb.jpg

post-25555-1179291834_thumb.jpg

post-25555-1179291914_thumb.jpg

post-25555-1179291991_thumb.jpg

post-25555-1179292064_thumb.jpg

post-25555-1179292127_thumb.jpg

post-25555-1179292188_thumb.jpg

post-25555-1179292248_thumb.jpg

post-25555-1179292316_thumb.jpg

post-25555-1179292380_thumb.jpg

post-25555-1179292446_thumb.jpg

post-25555-1179292570_thumb.jpg

post-25555-1179292626_thumb.jpg

post-25555-1179292686_thumb.jpg

post-25555-1179292742_thumb.jpg

post-25555-1179292829_thumb.jpg

post-25555-1179292899_thumb.jpg

mark,

have you got the passenger and driver floor mat? does it have the same shape for the GTR?

sure do arbress.. how u doin mate

the BNR32 ones are in my GTR at the moment but ill be keeping them when i get rid of it on friday. ive got 2 other for the rear and a spare R34 GTT one that fits perfectly. as well as 2 spot ones for the R34 and the trans tunnel for the R32. the R32 are the grey ones and the black ones are the R34. 2 sets of front floor matts are not pictured.

yes the spare drivers R34 GTT floor matt fits the R32. can use the rear matts from the R34 too they arnt as deep but work and reaches the heel..

sure do arbress.. how u doin mate

the BNR32 ones are in my GTR at the moment but ill be keeping them when i get rid of it on friday. ive got 2 other for the rear and a spare R34 GTT one that fits perfectly. as well as 2 spot ones for the R34 and the trans tunnel for the R32. the R32 are the grey ones and the black ones are the R34. 2 sets of front floor matts are not pictured.

yes the spare drivers R34 GTT floor matt fits the R32. can use the rear matts from the R34 too they arnt as deep but work and reaches the heel..

ok

hey man, How much for the complete aircon setup for the R32 GTST? My skyline is actually missing everything from under the bonnet. Could you PM a price or reply here.

Thanks

Adam.

Edited by Triptych
hey man, How much for the complete aircon setup for the R32 GTST? My skyline is actually missing everything from under the bonnet. Could you PM a price or reply here.

Thanks

Adam.

PM sent mate.

yeah got everything u need here in working good condition.

as requested pic added of GT badge, door trim piece next to the window and a spare 10mm hex bit that connects to a 21mm socket..

and a spare nissan flare unused.?

post-25555-1179305795_thumb.jpg

Do you have any Castor Rods or Front Lower Control Arms?

yep, good condition, no splits no cracks and straight same for control arms. see pics attached.

will u deliver bonnet?

im near mt cootha?

bonnet is too big to fit in any of my cars. and for price im asking doesnt seem to justify fuel cost either. pick up is prefered.

PM sent..

and where are you located...can i come and browse lol?

im located next to the hyperdome (2mins drive frm tuesday nights dinner venue.) im available for people to come browse after the weekend.

whatever ur looking for just make an offer.

ill reply to PMs tonight.

thanks

mark.

post-25555-1179367587_thumb.jpg

post-25555-1179367698_thumb.jpg

Hey mark I should be able to grab the air con setup. Might just have to give me 2 weeks if that is ok. Got car repayments to make next week.

Hey mark I should be able to grab the air con setup. Might just have to give me 2 weeks if that is ok. Got car repayments to make next week.

NP mate. A/C set up on hold. climate control electronic unit still forsale though

What's the deal with the 34 coilpacks?

They are on the R34 still. 1 of the coils breaks down intimetantly.. doesnt happen often just maybe once a week or so she will spit..

wow u got 6 front calipers? so 3 sets? how much are you wanting for a set? also are these 4pot ?

and one last misc q, do you have the front brake backing plate / dust shields?

cheers

yep got 1 set of dust shields but will sell that with 1 set of brakes..

1 set of front brakes are left sorry mate. they are un painted items from the R32 GTST halfcut. pistons are a little stiff but good condition still no leaks. and yes they are four piston calipers. ill take around $150 for them

thanks

mark.

able to have people come over to pick up stuff whenever.

also in regards to pull the heat shields off or dust shields. pull the holding pins out or get a screwdriver and leaver it out.. not too difficult. lol.

Make an offer. center airvent still forsale. LHS sold!




  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...