Jump to content
SAU Community

Misc Parts From R32 Half Cut And Odd Pieces... Pm Me What U Need


Recommended Posts

How you doing sau.

well ive got some lefted over pieces from my conversions.

LOCAL PICK UP PREFERED due to weight of most items.

Will trade anything for set of rims eg standard R32 R33 R34 rims or other parts..?

1 R32 GTST half cut (120,000kms), everything lefted part from slave cylinder, motor, box, loom, crossmember. the rest is left.

-good condition camber arms

-brakes 6xR32 front calipers 2x rears

-front hubs

-Power steering bits.

-hicas bits

- front light harness

-dash (NO BUBBLES NO CUTS, better condition dash than my GTR's :pwned: )

-all air vents LH SOLD

-digital climate control unit

-full a/c system, working condenser, pump, actuator etc. all lines too.

-door hinges

-GT badges (red)

-intercooler and most pipping

-glove box

-speedo drive cable SOLD

-brake lines

-brake master and clutch master

-pedals + brakets.

NO RUST IN FRONT OF SHELL.. good for someone who had a head on.

pm me what you need. ill take $800 for the whole thing.

$220 - R34 GTT intercooler and pipping (50,000kms)

ill install the R34 Gtt intercooler onto a R33 GTST for an extra $30 - good for RB25 upto 225kwATW with limited lag.. good upgrade for R33

$200 - R34 GTT airbox (40,000kms) new panel filter comes with snorkel

$50 - damaged alluminum R32 GTR bonnet.. was damaged coming off truck by crane see pic in last post.. bend in front and scratches.. comes with bonnet pin pins. SOLD

$25each - boost solenoids, BNR32, ECR33, ECR34, 200sx..

$15 each silicone hose 3 ply, 3"-2.5" , 2.5" blue, have standard hoses too.

$10 - exhaust heat shields,

from $20 each - GENUINE skyline + Nissan Floormats.. RRP $150-250 at nissan lol..

$30 - CA18 radiator

$50 - CA18 a/c units all working well..

$125 - CA18 digital + analog climate control

have more parts but thats all i can think of off the top of my head.

PM me with your offers and ill probably take them

thanks

mark.

NOTE** AIR VENTS IN GOOD WORKING ORDER. passenger airvent has crack on top right which has been repair not visible but works fine. centre is umarked and works fine.. (will be going on my GTR unless someone offers me something decent :dry: see pics.

post-25555-1179289340_thumb.jpg

post-25555-1179289402_thumb.jpg

post-25555-1179289459_thumb.jpg

post-25555-1179368929_thumb.jpg

post-25555-1179369002_thumb.jpg

Edited by markimak
  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

pic of R32 GTST cooler and R34 GTT cooler side by side.. look up to see my exceddy clutch box :pwned:

oh also got standard R32 GTST clutch plate, pressure plate ill take $10 for that.?

you can have the R34 GTT cooler installed for $220 exhanged.? or $250 drive in drive out. (approx 20mins)

post-25555-1179289949_thumb.jpg

Edited by markimak

Few more pics, floor mats are genuine SKyline and nissan items with SKyline badging on them.. off my BNR32 GTR still using 2 other front ones but will let the skyline floor mats go for the right price.

pics of R32 GTST rad over flow

Rad fan shrowd

Rad fan (viscous hub) CA18 and RB20

RB20 brake master and clutch master.

$offersCA18 ignitor

$25 - CA18 fuel pump suited to be a feeder pump for a larger fuel system

$15 - ok condition RB20 water pump worked well just replaced cause doing a tbelt.

CA18 + R34 GTT washer bottle

R34 GTT splash tray good condition

R34 GTT Neo cover

S13 lowered springs

S13 struts front and rear

S13 Struts front and rear kyob with cut king springs

space saver from R34 GTT new

Blitz silencer insert for exhaust off jasma muffler

R34 GTT spark plug cover

R34 GTT coil packs, they break down sometimes..?

R32 RB20DET Auto Tailshaft. was supplied an auto shaft with my manual half cut..?

PM me offers. i have charcoal canisters and other stuff that i cant think of.. pm me offers

of course item will go to highest offer at the time.. so best in best dressed..

post-25555-1179291563_thumb.jpg

post-25555-1179291629_thumb.jpg

post-25555-1179291693_thumb.jpg

post-25555-1179291779_thumb.jpg

post-25555-1179291834_thumb.jpg

post-25555-1179291914_thumb.jpg

post-25555-1179291991_thumb.jpg

post-25555-1179292064_thumb.jpg

post-25555-1179292127_thumb.jpg

post-25555-1179292188_thumb.jpg

post-25555-1179292248_thumb.jpg

post-25555-1179292316_thumb.jpg

post-25555-1179292380_thumb.jpg

post-25555-1179292446_thumb.jpg

post-25555-1179292570_thumb.jpg

post-25555-1179292626_thumb.jpg

post-25555-1179292686_thumb.jpg

post-25555-1179292742_thumb.jpg

post-25555-1179292829_thumb.jpg

post-25555-1179292899_thumb.jpg

mark,

have you got the passenger and driver floor mat? does it have the same shape for the GTR?

sure do arbress.. how u doin mate

the BNR32 ones are in my GTR at the moment but ill be keeping them when i get rid of it on friday. ive got 2 other for the rear and a spare R34 GTT one that fits perfectly. as well as 2 spot ones for the R34 and the trans tunnel for the R32. the R32 are the grey ones and the black ones are the R34. 2 sets of front floor matts are not pictured.

yes the spare drivers R34 GTT floor matt fits the R32. can use the rear matts from the R34 too they arnt as deep but work and reaches the heel..

sure do arbress.. how u doin mate

the BNR32 ones are in my GTR at the moment but ill be keeping them when i get rid of it on friday. ive got 2 other for the rear and a spare R34 GTT one that fits perfectly. as well as 2 spot ones for the R34 and the trans tunnel for the R32. the R32 are the grey ones and the black ones are the R34. 2 sets of front floor matts are not pictured.

yes the spare drivers R34 GTT floor matt fits the R32. can use the rear matts from the R34 too they arnt as deep but work and reaches the heel..

ok

hey man, How much for the complete aircon setup for the R32 GTST? My skyline is actually missing everything from under the bonnet. Could you PM a price or reply here.

Thanks

Adam.

Edited by Triptych
hey man, How much for the complete aircon setup for the R32 GTST? My skyline is actually missing everything from under the bonnet. Could you PM a price or reply here.

Thanks

Adam.

PM sent mate.

yeah got everything u need here in working good condition.

as requested pic added of GT badge, door trim piece next to the window and a spare 10mm hex bit that connects to a 21mm socket..

and a spare nissan flare unused.?

post-25555-1179305795_thumb.jpg

Do you have any Castor Rods or Front Lower Control Arms?

yep, good condition, no splits no cracks and straight same for control arms. see pics attached.

will u deliver bonnet?

im near mt cootha?

bonnet is too big to fit in any of my cars. and for price im asking doesnt seem to justify fuel cost either. pick up is prefered.

PM sent..

and where are you located...can i come and browse lol?

im located next to the hyperdome (2mins drive frm tuesday nights dinner venue.) im available for people to come browse after the weekend.

whatever ur looking for just make an offer.

ill reply to PMs tonight.

thanks

mark.

post-25555-1179367587_thumb.jpg

post-25555-1179367698_thumb.jpg

Hey mark I should be able to grab the air con setup. Might just have to give me 2 weeks if that is ok. Got car repayments to make next week.

Hey mark I should be able to grab the air con setup. Might just have to give me 2 weeks if that is ok. Got car repayments to make next week.

NP mate. A/C set up on hold. climate control electronic unit still forsale though

What's the deal with the 34 coilpacks?

They are on the R34 still. 1 of the coils breaks down intimetantly.. doesnt happen often just maybe once a week or so she will spit..

wow u got 6 front calipers? so 3 sets? how much are you wanting for a set? also are these 4pot ?

and one last misc q, do you have the front brake backing plate / dust shields?

cheers

yep got 1 set of dust shields but will sell that with 1 set of brakes..

1 set of front brakes are left sorry mate. they are un painted items from the R32 GTST halfcut. pistons are a little stiff but good condition still no leaks. and yes they are four piston calipers. ill take around $150 for them

thanks

mark.

able to have people come over to pick up stuff whenever.

also in regards to pull the heat shields off or dust shields. pull the holding pins out or get a screwdriver and leaver it out.. not too difficult. lol.

Make an offer. center airvent still forsale. LHS sold!




  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...