Jump to content
SAU Community

Installing Hks Gt-rs Questions: Banjo Bolt Position, Copper Washers, Oil Drain Gasket..


Recommended Posts

I just took the car for a quick run, its sounding good, drives fine. Damn the induction is LOUD, I like it. :)

There was abit of smoke/steam still coming out of the engine bay and upon closer inspection its directly where the dump bolts up to the turbo. I think it may be the Ultrablue 77B thats burning up, I put it on the dumpside gasket cos thats what the guy at the exhaust shop told me to do. Said it was sensor safe and should be fine. :paranoid:

Man thermal wrapping is expensive, I just unpluged the line and relocated. Much to my surprise it wasn't much coolant pissing out at all so its not bad. Its just sitting on the same metal lines the oil feed is. I just realised I didn't attach the picture in the last post, Manwhore can you have a look at this and tell me if its okay for the lines to sitting on this pipe?

Hey Manwhore I would like to do it but I can't atm as the car doesn't have wheels with proper tyres on it. I'll shall be getting new wheels next week and I'll let you know then.

post-8121-1179815263_thumb.jpg

That line hitting the aircon pipe looks fine to me, just put a bit of plastic or rubber insulation around it just to be safe, by the way are you using the lines that came with the brand new gt-rs kit? or did you buy the gt-rs second hand and got lines custom made up?

awesome, let us knwo then.

If not much coolant came out, then that means you MIGHT have air in the system. If it was me, i'd bleed it. Even after I drained the radiator, when I undid the bajo, about 4-4.5 L came out.

Man thermal wrapping is expensive, I just unpluged the line and relocated. Much to my surprise it wasn't much coolant pissing out at all so its not bad. Its just sitting on the same metal lines the oil feed is. I just realised I didn't attach the picture in the last post, Manwhore can you have a look at this and tell me if its okay for the lines to sitting on this pipe?

Hey Manwhore I would like to do it but I can't atm as the car doesn't have wheels with proper tyres on it. I'll shall be getting new wheels next week and I'll let you know then.

nizmo, the lines are from the GT-RS kit, it was second hand but its what came with the kit originally.

Manwhore, its just resting against it. :) Like theres a natural bend in the line and that pipe stops it from doing its full bend, the coolant feed is sitting on that line as well though you can't see it in the picture.

I'll bleed the system, the amount of coolant that came out was probably wasn't much because as long as I was holding the braided line up it no more would come out until I bent the line lower allowing coolant to spill out.

The whole time the engine is running and rocking from side to side, the S/S line will rub thru the alloy a/c line

I will give it 1 week maybe 2 before your A/C stops working. Best to space it away or put a rubber sleeve on it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...