Jump to content
SAU Community

Recommended Posts

hey guys i got a set of rims for sale

the brand is ziet intensive and they are very light considering the size of them

they are 19x10 +23 offset for the rear. Has stretched 235/35 nankangs but will need replacing

19x9 +31 offset for the front. Has nankangs 225/35 and they are only about a month old

they came from japan about 10-11 months ago and were purchased from otomoto. They are in great condition and look really good. They are 4 and 5 stud so they can fit 180sx/s13 and skylines and 200sxs

im looking for $1600 as is and they are already off the car and ready to go

pick-up only for the time being

located in blacktown

for more information call peter 0407 008 651

rims3.jpg

rims2.jpg

rims1.jpg

Edited by 4admrn
Link to comment
https://www.sau.com.au/forums/topic/170409-syd-19inch-deep-dish-rims/
Share on other sites

would they be sticking out of the guards on a series 2 R33? or will it be like yours sitting inside the guards?

just in the process of arranging my series 2 and if all goes well ill send you a PM

im guessing they'd stick out im not quiet sure... but if you want when you get the car drop me a pm and if their still available you could trial fit them on

im guessing they'd stick out im not quiet sure... but if you want when you get the car drop me a pm and if their still available you could trial fit them on

that might be a problem coz im in melbourne but ye when i get the car ill find rims with similar off set and try them on to see if ti sticks out or not. if it dosnt then i will be in contact with you. can you send them interstate? id be happy to organise it all.

thanks

Ash

  • 1 month later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...