Jump to content
SAU Community

queens b'day monday cruise


Recommended Posts

Guest Ricky_B

hey i wanted 2 see if we can get a cruise going on the public holiday monday like start in sydney and go down the coast or sumthin. im too unorganised 2 make a cruise so i ned sum input from a professional. i was thinkin we could meet up at the kfc on the cumberland hyway near the m4 that way we can go either up or down the coast or inland.

neways ill let yas think about it

yullah bye

Link to comment
https://www.sau.com.au/forums/topic/17051-queens-bday-monday-cruise/
Share on other sites

my advice... meet at the kfc on the cumberland hyway near the m4 and then cruise along cumberland hwy towards M4... turn right onto M4... then take reservior rd exit and turn right. turn left at the first set of lights onto the great western hwy and then left at the first set of lights. Follow the road you are on untill you get to a round about... turn left. follow that to the next round about... watch for copers... EC should be infront of you... turn right. follow that around untill you get to gate 7 (?) competitors entry... turn left and enter the competitors entry!!! keep driving and look for all the lines!



  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...