Jump to content
SAU Community

Airflow Meter

Ben101

By Ben101,
in General Maintenance

 Share

Recommended Posts

Ben101 Contributor

Ben101

Posted
Posted

Hey pplz,

My r32 gts-t doesn't always seem start without me having to give it some gas

as it stands its stock apart from a cat back and a walbro fuel pump i've done some searching on

the forum, and everything I read seams to point to the air flow meter

the starting problem, the car been jerky when you lift off then go to

accelerate again, would the Z32 upgrade be a wise move as for furture mods, am

I to belive that the stock computer will handle it no worries?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/171523-airflow-meter/
Share on other sites
Craved Grand Master

Craved

Posted
Posted
Cheers guys I'll look into the gtr thread

Hey craved you still got your ninja, back in 2005 I had problems with

mine and you were giving me some suggestion?

yes mate still got it, just been resprayed and the front forks rebuilt.

havent ridden it in over 6 months though due to the work on it, but its almost put back together.

Link to comment
https://www.sau.com.au/forums/topic/171523-airflow-meter/#findComment-3164102
Share on other sites
RB30-POWER Mentor

RB30-POWER

Posted
Posted

Shouldn't need to touch accelerator to start it.

You will need to check the throttle position sensor is set correctly and working, especially idle position, check the coolant temp sensor if you think its lacking enrichment, check the base idle, check for vac leaks and maybe clean/service the air regulator.

After fixing that it should start at the touch of the key first time, every time.

Also try priming the pump for a few secs before start, see if it helps, this could point to a faulty check valve in the pump if it starts after the rail is primed with pressure.

Link to comment
https://www.sau.com.au/forums/topic/171523-airflow-meter/#findComment-3164418
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • PranK
      Shoota's R33 GT-R RB30/26

      By PranK · Posted

      It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • ShezzDogs
      R34 Skyline Sunroof Won't Tilt/Vent

      By ShezzDogs · Posted

      Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...