Jump to content
SAU Community

calder this fri?

dAVE

By dAVE,
in Victoria

 Share

Recommended Posts

Al Grand Master

Al

Posted
Posted

Dave don't forget a helmet, and to wear a long sleeve top.

Personally i would wait for another Heathcote, as it is cheaper and you hace alot more runs, as lowlux has stated.

I should be able to hear you going down the straight, from my house :(.

Link to comment
https://www.sau.com.au/forums/topic/17492-calder-this-fri/#findComment-362185
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

yeah true.

no more Sundays. Thre are 2 fridays a month now instead... but that day, it was race and the faster you got back to the start the sooner you raced!! lol. was great.

But if you get to calder about 5-5.30pm, and get out there straight away after scrutineering... you can get about 3-5 quick runs in beofre 7pm when everyone gets there.

something to think about

Link to comment
https://www.sau.com.au/forums/topic/17492-calder-this-fri/#findComment-362988
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...