Jump to content
SAU Community

Recommended Posts

  • 1 month later...

My clutch is not engaging until right at the floor, still drivable but you can feel it should have more to it.

I've bleed the slave cylinder as mentioned above but its still the same?

The Fluid dampener you spoke about, Can that be bleed as the same process of Open, Pedal down, Close and then pedal up?

I was told it was a heavy duty clutch but not sure on what kind exactly, i had a quick sus by moving the rubber from underneath and seen an extreme purple plate.

Is there anything else i should be looking out for?

  • 1 year later...

So i had a good read of this thread and came up with the solution.

After bleeding the master.

On the slave cylinder If the bleed nipple is not at the high point, it wont bleed the air out.

post-89755-0-65855700-1378958539_thumb.jpg

So i took mine off, with a bit of tape to stop the piston coming all the way out.

Then i held it with the bleed nipple at the high point, and opened the bleed, pushed the piston in, closed the bleed, let the piston out.

Repeat until all air is gone, keep an eye on the fluid level up top.

post-89755-0-85601000-1378958890_thumb.jpg

Rinse well and get all the brake fluid off.

post-89755-0-45933200-1378958956_thumb.jpg

Works! :banana:

  • 2 weeks later...

On the slave cylinder If the bleed nipple is not at the high point, it wont bleed the air out.

The bleed nipple should always be at the high point. If it's not, it's in the wrong hole or you bought the cylinder out of the wrong end of China

Yeah right.

Thats what you get for buying a car from idiots. Bits put together wrong. So many....... Anyway, another one to fix.

Ill swap them around.

It's not such a bad thing. Of course bleeding is a pain in the arse but that's about it. Make sure before you swap it around, you check to make sure the banjo fitting has a machined surface to crush the copper washer against. I have seen some cylinders actually made incorrectly. In those cases, you will need to leave it as is.

  • 2 months later...

why not reverse bleed slave to master?

- empty reservoir

- push new oil from can from slave to master, then no bubble

i reckn this is better

You should try to avoid pushing air into the master cylinder. It is bad practice. There are places where the air can be trapped and you will have difficulty getting it out.

That's why you should always bleed the master cylinder on the bench before fitting a new one.

I'm unsure how you would feed fluid into the slave cylinder anyway. if you're just attaching a hose to the nippple and the hose sits in the bottle of new fluid, that won't always work either. It is quite easy for air to be drawn past the threads of the bleed nippple into the system.

This method may have worked for you though. I'm not saying it won't. I'm just saying it is less likely to work in all situations but moreso it can cause problems not easily diagnosed.

  • Like 1
  • 2 years later...

Did this today as I replaced my master and slave cylinders. I already have a braided line so I only needed to bleed master and slave. I was fairly anxious about getting this right and went back and forth bled both until I was satisfied. I found it was easier and I had more control bleeding the slave by myself by pushing in the fork as it allowed my to do it slower and therefore see exactly the condition of fluid coming out. I did have an issue with the pedal only half responding in its normal way when I thought I was done, so I just got under and re-bled it all until I actually got all the air out and the clutch responded as normal. Went for a test drive and everything works really well now, so am happy with getting this done.

Yeah also doing this today. Clutch pivot snapped and I've ended up with a new clutch etc. When the pivot point snapped, the slave rod bent out to the side and in order to get it back in I needed to drag the boot off of the end of the slave. Need to fill the entire thing with no pedal tone at all. Fun fun. -_-

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...