Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Err how is that possible? Is your exhaust connected to your intercooler? :(
:laughing-smiley-014:

Luckily it didn't go the other way and end up in your sump hey? or even worse, in the flux capacitor.

ok ok... know how a turbo works? obviously not you keyboard monkeys...

when your ceramic turbo wheels blow at 6000rpm, where do the peices go? out the exhaust AND ALSO through your intercooler..

so who said they were connected?

fully sick yea??

god some people just need to grow the f*k up and read between the lines :(

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/page/3/#findComment-3265020
Share on other sites

assuming you drive a commonhore t like me...

well if its an s1 it would be bits of steel in your cooler core + through engy eventually out the exhuast.. if they are small enough and after they have scored shit pretty well... like sand.

if s2 nylon.. same deal.. potentially less damage inside if it makes it through your coolers core...

ceramic exhuast side only....

never heard the flutter out of my car... high or low throttle... dunno... every time i think fluter i think of the dumb 200sx driving twat indian near me who always wants to run... hes been pulled over for trying to push me into a race... he still trys...

best part.. was @ wsid once with his 20" wide 3" thick steel rimmed sr with his mates trying to show everyone up...

not only did i beet him but so did a drunk smartass in a combi.. .. was awsome for a laugh

200sx that pulls late 14s.. MUAHAHHahahahahaha what a dumb twat...

Link to comment
https://www.sau.com.au/forums/topic/176614-flutter/page/3/#findComment-3265300
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...