Jump to content
SAU Community

Recommended Posts

I have a set of 4 brake rotors for sale which came off a 1995 Nissan Skyline R33 RB25DET.

* My reason for selling is I have just upgraded to the new DBA Rotors.

* These are the original stock rotors which have done 72,000km.

* They were last machined about 5mths ago and are in good condition.

* Pics available at:

http://skylines.pnc.com.au/pics/ben/rotor/rotor7.jpg

http://skylines.pnc.com.au/pics/ben/rotor/rotor8.jpg

* I have no idea what they are worth and im not too technically minded (as far as what they will/won't fit) so go easy...

Link to comment
https://www.sau.com.au/forums/topic/17685-r33-stock-brake-rotors-rb25det/
Share on other sites

  • 3 weeks later...

I bought the DBA's in the recent group buy and i think they cost me like $900ish fitted for front n back.

I haven't noticed any difference with them for a couple of reasons...

I only did 300km on the new DBA's before hitting them way -too- hard at a trackday resulting in glazing them and giving em a wash in brake fluid :P . So after that trackday I got new fluid put in and my brake pedal just doesnt even feel normal let alone better from the DBA's so i think i need to get them looked at again (in about 2wks before i hit the next trackday).

Really though i dont think in normal street driving you will feel a difference i bought them purely for that little bit extra at trackdays (which im yet to notice because of above and coz my tyres are bald).

  • 4 weeks later...

You'd have to measure them with calipers to get any indication of how much they're worth. Near-new I would say they'd be worth maybe $200 the pair machined (machined because without doing that there's no way to determine their thickness with any accuracy), or if worn down below the halfway point maybe $100 the pair? New rotors are 30mm thick, and the run-out point is 28mm.

Unfortunately there's no way to tell how much they've been worn just by stating the odometer reading. The amount of wear they've had will be largely dependant on driving style and type of pads used, and for all you know they could be the 2nd or 3rd set of rotors used on the car (entirely possible if the car had done any trackwork in Japan).

If you've been running the Ultimates on them since they got machined 5 months ago, you might find they're up for machining again.

  • 5 weeks later...

Measurements are:

Front Left: 28.20mm

Front Right: 28.98mm

Rear Left: 17.67mm

Rear Right: 16.50mm

I believe they are good for 1 more machining but do not need to be machined yet (surface is very smooth).

$200 for all 4 pickup

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...