Jump to content
SAU Community

Recommended Posts

Hi,

I'm a bit of a DIY noob. This weekend I am going to flush and replace the coolant in the radiator. From what I've researched, it just a matter of undoing the bolt below the rad, undo the top cap, drain, fill up with tap water and run engine at max heat for a minute or so, repeat until tap water flushes clear. Redo nut/bolt and fill with coolant mixture. Run a bit and top up if needed.

Have I missed anything? Do i need to 'bleed' the thing?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/177352-flushing-and-replacing-coolant/
Share on other sites

to flush it properly you need to either remove the block drain plug under exhuast manifold, or its usually easier to remove the thermostat, or else the thermostat traps old water in block still.

you will need to bleed it when you refill it, at the bleeder nipples.

also be careful about using the drain tap, usually if the radiator is old, they just snap off and you need an entire radiator, its far easier and safer IMHO to remove the radiator lower hose. that way there is no suprises.

  RB30-POWER said:
to flush it properly you need to either remove the block drain plug under exhuast manifold, or its usually easier to remove the thermostat, or else the thermostat traps old water in block still.

you will need to bleed it when you refill it, at the bleeder nipples.

also be careful about using the drain tap, usually if the radiator is old, they just snap off and you need an entire radiator, its far easier and safer IMHO to remove the radiator lower hose. that way there is no suprises.

Thanks, after reading that i'm thinking it's not really that simple :)

1. Where's the exhaust manifold? Or Thermostat?

2. Where are the Bleeder Nips?

3. What's a Drain Tap?

4. Where's the Radiator Hose?

Sorry!

Edited by webng

This is how i flush cooling systems at work:

If you have a drain plug that is accessible on the radiator use it to drain the radiator, otherwise drop the bottom hose off the radiator.

Make sure your heater is switched to full hot, you may need the ignition on if you have climate control. (This flushes the heater core too)

Pull one end off the most accessible heater hoses and put a garden hose down it tightly (remove the nozzle and just poke the hose in)

Turn the hose on fully and watch the old coolant flow from the radiator drain hole and the spot where you removed the heater hose.

Let the water run until it runs clear. Remove the garden hose

Put the radiator drain back in and leave the heater hose off.

If your engine has a air bleed screw in the cooling system/intake mannifold loosen it now.

Start filling the system with coolant keeping a close eye on the heater hose and pipe where it was removed from.

DO NOT REFIT IT UNTIL COOLANT FLOWS FROM IT. WATER IS NOT COOLANT

This way you push out all the air in the system and all the excess water (otherwise you wont fit much coolant in)

Leaving the heater hose off helps with air pockets in the system in a BIG way

Once it starts to flow the color of the coolant put the hose back on and continue filling the system with the correct percentage of coolant concentrate.

When it won't take anymore coolant start the engine and get it circulating by holding the revs up slightly.

While you do this you should be able to add more coolant/water.

Leave the radiator cap off until there are no more bubbles coming up through the coolant and both radiator hoses are nice and hot.

If you have an air bleed screw do it up once coolant flows steadily from it.

This means that the thermostat has opened, it can take quite awhile so be patient

Once both hoses are hot you can refit the cap and take it for a drive (keep and eye on the temp guage)

Don't turn off the heater tap until you feel hot air coming out of the vents. (cold air means you have most likely an air pocket in the system)

Have fun :)

  webng said:
Thanks, after reading that i'm thinking it's not really that simple :)

1. Where's the exhaust manifold? Or Thermostat?

2. Where are the Bleeder Nips?

3. What's a Drain Tap?

4. Where's the Radiator Hose?

Sorry!

1. If you dont know where your exhaust mannifold is maybe you shouldnt be doing this ;) Thermostat in a housing at the engine side of either top or bottom radiator hoses.

2. Bleeder nipple will be on your intake mannifold and will say do not open when hot next to it on a little gold sticker.

3. Drain tap will be on the bottom of your radiator, if you have a drain tap that is.

4. Radiator hoses run from the tanks of the radiator to engine.

I think either invest in a workshop manual if you can find one or take it to a garage. If your in Brisbane i can do it for you.

Deren :)

  Godzilla32 said:
1. If you dont know where your exhaust mannifold is maybe you shouldnt be doing this ;) Thermostat in a housing at the engine side of either top or bottom radiator hoses.

2. Bleeder nipple will be on your intake mannifold and will say do not open when hot next to it on a little gold sticker.

3. Drain tap will be on the bottom of your radiator, if you have a drain tap that is.

4. Radiator hoses run from the tanks of the radiator to engine.

I think either invest in a workshop manual if you can find one or take it to a garage. If your in Brisbane i can do it for you.

Deren :)

lol, maybe i shouldn't, but it's worth a try anyways. I don't mind getting my hands dirty and learning bit by bit.

Really appreciate the info, thanks for that. I'll have a go this weekend. :)

Your welcome, the only thing you can do wrong is drive it with an air pocket in it and over heat it...just run it with the cap off and make sure all the air is out before you drive it and then watch you gauge. :) If the gauge rises while you drive it and it wont read normally (ie too hot) pull over and crack the cap to the first click to release the air then if theres no coolant coming out carefully remove it the rest of the way and top it up then it should be sweet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...