Jump to content
SAU Community

Recommended Posts

Hey all,

I posted a topic on here a while ago asking advice on what kind of mods i should get for my r33. My car already has an Apex 3 inch exhaust, blitz FMIC and high pressure fuel pump. After a lot of deliberation, ive come to this list, written in order.

1. K & N panel filter

2. Apexi Powerfc (with or without Handset?? advice??)

3. Bigger Injectors (im guessing around the 500cc mark?? or 740cc?? advice again??)

4. Then from that, id say camshafts??

5. Bigger Turbo

Im aiming at around 200 rwkw (at least) on stock internals. This car is also going to be a daily driver so i dont really want to dial up the boost much if at all. I basically want to get as much power as i can safely out of the stock internals.

Is there anything i have missed out in this list?? And finally, how much would this list cost me roughly all up?? including a proper tune and labour to install etc???

I know these are pretty novice questions, but any help would be much appreciated!!!

Link to comment
https://www.sau.com.au/forums/topic/177404-noob-questions/
Share on other sites

1. Filter not too expensive about $80 i think

2. Power FC. If you can find one, buy it. They are around $1K

3. Bigger injectors are good, 550cc would be the mark. You wouldn't have to go to 740 for 200kw. Not sure on price

4. Cam shafts, good idea, pretty expensive tho

5. Again, expensive. Look at some high flowed turbos. Slide has some (trader on sau)

Link to comment
https://www.sau.com.au/forums/topic/177404-noob-questions/#findComment-3240465
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...