Jump to content
SAU Community

Recommended Posts

hey all..

vicroads have given me 2 weeks to get a rwc as when i got the car, it didnt come with one.. so before i chuck on my parts, need to get the rwc done.

only issues i can see are bov, rear tyres and passenger side seat belt which is screwed..

i can easily replace the rear tyres thats no problem;

where can i go east that i can get a road worthy done?

i have searched but i find a lot of members PM with information that cna help.. need this done asap! please help!!

cheers

Josh

Link to comment
https://www.sau.com.au/forums/topic/179123-rwc/
Share on other sites

hi mate.

as for getting a rwc i recermend any repco service center. they have warenty and do a realy good a nd through job as all repco stoers are inderpendent. repco only helps with suplying parts, waranty adn workshope equpment.

there should be one in your local area, as for hourly rate its $99/h. if your in the eltham area i would recemrmend andrew timby at 13 brougham st eltham. ph 9439 7574

chears brent

Link to comment
https://www.sau.com.au/forums/topic/179123-rwc/#findComment-3265022
Share on other sites

haha it does sound like vu's.. must of gotten names mixed up :nyaanyaa:

ive gone to a guy in dandenong who didnt give me the sort of RWC i wanted but met me half way... i just had to replace acouple of parts that will save my ass while driving and braking etc., other than that, didnt have to change one major part ;)

Link to comment
https://www.sau.com.au/forums/topic/179123-rwc/#findComment-3267944
Share on other sites

hey 180drifter if you need a factory blov i have one i can loan you.

if ya need it for your RWC, all i do when i get done is swap my HKS BLOV for the factory and then get it marked off and swap it back.

so if ya need it for a loan pm me and we can swap it befor ya go. i can fit it in about 10min too

Link to comment
https://www.sau.com.au/forums/topic/179123-rwc/#findComment-3274721
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...