Jump to content
SAU Community

Recommended Posts

hey guys, just wondering if anyone else has had this problem before, i was racing my car at the drags and had no traction so i ran a 14.6 at 163km/h but anyways when i went to do my 5th run for the day i hit 4th gear and it just didnt wanna rev like it had lost all its power wouldnt gain speed or rev's. and im pretty shore while i was holding threw 3rd it was pinging i could hear a slight taping noise all the way threw 3rd. now i just wanna know why i had no power in 4th?????? it was 1.30pm and probly 30'c max that night i went for a drive and went threw all the gears hard and it didnt miss a beat pulled all the way threw 4th ??????? whats going on

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/
Share on other sites

1400r. oh thats very helpful info i didnt think the ecu did that on the skyline never read about it b4 thats all but it makes sence, thanx for your help guys i guess i need to run it on dyno again n get a retune, the last place that did it are a bunch of ................. only went there cause they are the only place in my town with a dyno but i will travel this time

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/#findComment-3297438
Share on other sites

the intake sucking closed can be fixed pretty cheap.

search for "intake" by user "rev210"

he had a little article about his simple and effective fix.

also, if you could hear pinging while drag racing, with a helmet... it must have been pinging pretty farking badly..

and it would explain why the ecu woudl retard the timing so you couldn't kill the motor.

I'd definitely have it checked on a dyno to see how the current tune is..

is it tuned?

is there an aftermarket ecu in there?

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/#findComment-3302711
Share on other sites

here is the link for the intake mod

http://www.skylinesaustralia.com/forums/in...9&hl=intake

stock ecu and 11 psi and pinging..

where exactly are you?

just go to any dyno place to do a power run and ask to get a print out of your A:F ratio reading.

normally a stock ecu'd R33 goes rich.. if your's is leaning out, it might be a fuel pump/filter/injector issue.

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/#findComment-3303038
Share on other sites

5hrs up the coast from brissy Gladstone. . . There is only 1 dyno place in town and they know bugger all. Charged me $60 to clean the T/B when i figured out all they used was a can of T/B CArby cleaner for $6.00

yeah thats not a bad idea, fuel pump/filter/injector. going to do a compression test, then go from there i think.

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/#findComment-3303198
Share on other sites

hey guys well i do have a piggy back computer its an safc it is tuned well was about 3 mnths ago so yes i think im up for a retune but dnt want to go anywear hear again. thanx for all the input guys and yeh im not 100% if it was piniging or not but only one way to find out i guess (dyno)

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/#findComment-3303434
Share on other sites

GTST, i have a print out and i scaned it but it didnt bring up the numers like on the x and y axis and it wnt upload it for sumreason from wha ti can see it runs approx on 12 till the car hits 120kmh then it dips to 11.5 and slowy rises back up to 12 towards 170kmh, and no there has been no modifications since this tune all i have done is change the oil and its running the same oil just new stuff, it had new plugs gapped at 0.8mm and the mods include fmic/3inch dump pipe/3.5inch cat back, stock cat, apexi safc, pod filter, boost controller set at 11.5psi

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/#findComment-3306256
Share on other sites

if it is the intake sucking closed, you can do the mod in the link above.

it will cost you next to nothing.

but the only way to see if it is sucking closed is on a dyno.

or remove bonnet, strap a mate on the front guard, then go for a fang and ask him what he can see.

could be fun.. ;)

Link to comment
https://www.sau.com.au/forums/topic/181485-no-power-in-4th/#findComment-3307137
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...