Jump to content
SAU Community

Jap Sticker

HELLRAISER

By HELLRAISER,
in General Automotive Discussion

 Share

Recommended Posts

HELLRAISER Explorer

HELLRAISER

Posted
Posted

Hi,

My R33 was imported to AUS in May 07, and at the time it had 95000 on the clock(i am the first owner), which means that i would need to do the timing belt and the water pump soon, but i noticed JAP sticker, its on the cover of the timing belt saying 91365 KM, and somthing else in jap which i am trying to figure out ... i am thinking that they replaced it before the car got to AUS, other belts seem new, water pump has a slightly different colour, and the screws around and on it seem to be worked on,

I am not shore, should i risk or not??? if it was done no point doing it again and plust it cost 6 7 800 bucks ...

I will take the cover of to check the belt for cracks and see (it should still look new)

But if the sticker confirms that it was done ... i will be the happiest :P

Can anyone translate it to me, plz

Thanks

post-39195-1188116643_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/182321-jap-sticker/
Share on other sites
HELLRAISER Explorer

HELLRAISER

Posted
  • Author
Posted
Your sticker says...

Timing belt change

Date: 24 November 2006

Odo: 93165

Just a sticker though, anyone could have put it there! Still if the belt looks in new condition you can be fairly confident it has been done.

Hi,

Thanks for that pal, i will still take the cover off to have a look.

I dont think that anyone would put somthing like ther just to f...ck someone up if it wasnt done, at least it wouldnt do it, but u know ther r all sorts of ppl out there ... but again noone can benifit from it

Thanks a lot again.

Link to comment
https://www.sau.com.au/forums/topic/182321-jap-sticker/#findComment-3309738
Share on other sites
HELLRAISER Explorer

HELLRAISER

Posted
  • Author
Posted

hmmmmmmmmmm

g i h8 dodgey jobs n ppl ... do it properly or dont f.. do it

loosers

Based on things that i have seen on the car i am positive, that its been done, but just 4 my own peace of minde, i will take the cover off to check for craks ... or if it look new

Link to comment
https://www.sau.com.au/forums/topic/182321-jap-sticker/#findComment-3311901
Share on other sites
HELLRAISER Explorer

HELLRAISER

Posted
  • Author
Posted
HELLRAISER - You said that you think it will cost 6 - 7- $800 to do your timing belt???

Youre getting ripped off if you've been quoted that much!

Yeah pal, i know, thats for d water pump and a belt( to be more specific $890), quoted to me by a shop thats advertasing on this webpage, i know that they have good reputation but ... its way too much

Link to comment
https://www.sau.com.au/forums/topic/182321-jap-sticker/#findComment-3314375
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...