Jump to content
SAU Community

Bbs Rims 17 X 8 & 17 X 9 +35 +35 (5x114.3)

burgO.

By burgO.,
in Classifieds

 Share

Recommended Posts

burgO. Collaborator

burgO.

Posted
Posted (edited)

Hey guys, have a set of 4 rims here, when i purchased them one had bad gutter rash and the other a small buckle, these have both been professionally fixed ($240 later)

i'm interested in trading them for another set of rims, i have tyres to put on them depending on the deal etc. i'm not really sure what they're worth but i'm more keen on the trade

if i don't get any interest by the time i get my suspension in my car (2 weeks or so) i'll be putting them on my car so i'm not too phased, just like to see whats out there

So anyone with 17s or 18s looking to swap send me a pm, cash adjustment either way if necessary!

Located in Brisbane

Cheers guys

post-37002-1189941256_thumb.jpg

Edited by burgO.
Link to comment
https://www.sau.com.au/forums/topic/185279-bbs-rims-17-x-8-17-x-9-35-35-5x1143/
Share on other sites
Oblivion Grand Master

Oblivion

Posted
Posted

Not really after a trade buddy, but my R32 gtr rims are up the plates to be sold.

Not in a rush either as i dont have my new set yet.

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Fuark, at least the motor survived. What brand was the fitting that snapped?
    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...