Jump to content
SAU Community

Attempted Break In

Ryanrb25

By Ryanrb25,
in South Australia

 Share

Recommended Posts

MikeyGTRmike Rising Star

MikeyGTRmike

Posted
Posted
hey brittz

the pager alarm is an alarm that when it is set off it lets your pager know so it beeps at you my bf has one on his car and the pager can be set off up to 500meters away. It has a little screen on it with a pic of a car too haha it tells you whats happening if the cars been hit or theres a door open etc.

Its definatly worth the money some of them come with remote start so you can warm your car up etc.

If you want to get a quote go to Angs audio shop on north east road. it cost my bf $850 thats the top of the line one too mates rates haha.

Go in and talk to ang tell him lauren aka pinkbits sent you down there he should fix you up

Lauren

i got my viper alarm (top of the line with remote start) off the net for 350, and i got it installed by the boys at auto bahn cost me 310 for the install. works great... i rest a little easier now when i leave my car at the shops caus emy pager goes off if someone so much as farts near my car....

my advice is check the net for cheaper alarms if ya wanna save yourself some cash

brittz Contributor

brittz

Posted
Posted

about the whole pager things, do you have to get a new alarm? because i already have a pretty good alarm and dont really wanna spend heaps of cash to get a newer one so it has a pager thing. cant someone just add it on?

Dohmar Grand Master

Dohmar

Posted
Posted
about the whole pager things, do you have to get a new alarm? because i already have a pretty good alarm and dont really wanna spend heaps of cash to get a newer one so it has a pager thing. cant someone just add it on?

It depends on the particular model. The alarm needs to interface with the gps+gsm unit... some of the Autowatch series have this feature. Otherwise the other ones I know of are all in one units (and are generally monitored and uber pricey)

-D

PS If you want to talk alarms, give George at Adelaide Pro Sound a tingle. He did a great job on my r32...was worth the drive south heheh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Watermouse
      Original window sticker?

      By Watermouse · Posted

      I got a full sheet set of OEM copied stickers to replace all the faded engine bay ones, great quality too.  Came from England. Someone like that should be able to to make u up what u want so long as u have a quality image to show them 🤷🏻‍♂️
    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
×
×
  • Create New...