Jump to content
SAU Community

Nark and Marks thread about wheels that look horn on black 32s :)


Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

good stuff nark.. just make sure they are the right offset... i went and checked out my ride to be.. meggala's r32.. and had a second look at tha volks on it.. they are actually 81/2 on the rear.. i got a feeling the offset is a bit off for em.. so i would have to roll the gaurds more than i really want to..

might sell em and look at getting some white p1 buddy clubs, not sure yet... lol isn't this sad i already got a million and one things i wanna to do it and its not even mine yet ROFL..

mark

bahaha man i only just ordered mine from japan and i already had a stereo system for it :) 6 months later my car finally came and i only put the headunit in it haha

a nice white R32 GTR :) looked sexamaphonic! i just got to get some rubber put on em... im gonna take em on wednesday to get a quote on it

hgahah very true, i'm such a whore takling about my own rims to be in ur thread hahaha, i got a quote on the white enkie tarmac evo's

17x8 all the way around 450 each, but they dont have stock until another 6 weeks grrr

mark

:P the guy pulled out... apparently the guy he was getting his rims off stacked and buckled the rims sohes got none or something... he called me at like 10am which is way b4 i normaly get up so im a little vague onm what he actually said... but who cares what he said no rims for me :P now i gotta find a decent set for the same privce i actually like.

:P i want wheels.... now

today... DAMN IT!!

:P

&$&% %*&%*& %*%*%^ *^%*^

i might just put some decent tyres on the stockies and spend the money on a carbon fibre bonnet and painting my boot and sideskirts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...