Jump to content
SAU Community

Nark and Marks thread about wheels that look horn on black 32s :)

inark

By inark,
in Victoria

 Share

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

inark Grand Master

inark

Posted
  • Author
Posted

nah theres a GTST one for the 32... just need a GTR bonnet latch... which i can get my mum whos in NZ at the moment to get cheap.

qikshift Rising Star

qikshift

Posted
Posted

nark u mofo i wanted steves cooler !!! grrr u can get the dump pipe have u seen it its phat as LOL hehehhe.

btw if u do buying it u may want to plumb a stock or after market bov into it... as he wasn't running one.. sure hte cooler sounded crazy but wasn't good for hte turbo :)

mark

inark Grand Master

inark

Posted
  • Author
Posted

BSA 264s in Silver 17x8 with Falken 235s all round = $1560

EVO Tarmac EVOs 17x8 with Falken 235s all round = $2570

Speedy wont fit my car cause of stud pattern....

think i'll go the BSAs

inark Grand Master

inark

Posted
  • Author
Posted

meh u can get the cooler then i'll get these other wheels... will wait to speak to dex on saturday incase he wants to sell his wheels later on and hold off til then.

qikshift Rising Star

qikshift

Posted
Posted

haha, nah i'm going to hold off on the cooler for the moment... ive driven phat32.. as i was going to buy it just didn't have ht emoney at the time... it was just a lil bit laggy for me with the 3inch piping i found.

might grab the 33 rims off him though so i have something to use while i sell the volks.

mark

inark Grand Master

inark

Posted
  • Author
Posted

hey u know those wheels u like on that RB25 R32... see the BSA 109s http://www.donnellans.com.au/wheelsfolder/bsa.htm they look close yeah? powder coat em in white :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...