Jump to content
SAU Community

Recommended Posts

1. Brand New Tomei Cam Gear for RB engines. (INLET ONLY)

2. Flame thrower Kit -- $ 100

post-12776-1191408683_thumb.jpg

3. Brand New Intercooler 600 x 300 x 76 (sprayed HKS at front)

4. Brand New Dual Core Aluminum Radiator 670 x 485 x 50mm for R33 / R34

5. R33 GTR front Grille (midnight purple)

6. R33 GTST door trim (Driver side)

7. HKS old type BOV

8. R34 GTT Front Bar (Black 2 tone paint) -- $ 150

9. R34 GTT Bonnet with safety pin + 2 Led washer light (Black 2 tone paint)

post-12776-1193371165_thumb.jpg

10. R34 GTT Rear Bar (Black 2 tone paint) -- $ 200

11. Brand New complete HID kit 8000K H1

12. R33 R32 Stock turbo (very good condition) -- $250

13. R34 GTT stock fuel pump -- $60

14. R34 GTT stock gear shifter -- $30

15. R34 GTT stock clutch (Pull type) inc pressure & clutch plate, bearing and Flywheel -- $300

16. R33 GTST / R34 GTT stock BOV -- $ 30

Everything must go... !!!

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

What brand is the intercooler??

Plus where would i be likely to find the piping kit for the cooler?

Cheers

No brand when i bought it.. but i think it's similar to hybrid.

you can custom make piping or buy the standard piping for hybrid about $200 or from ebay ;)

is that a real grille GTR or copy? if so how much to ship to tassie

It's 100% genuine. What is your postcode ?

Lots of interest from interstate... Where are the local boys and gals ??? s

Still prefer local pick up... :happy: Can deliver for free within 10km range from Sunnybank.. how's that sound... :thumbsup:

hey is the radiator a direct replacement for an r33 gts-t. WOuld u sell for $150 pickup

Yes, it's a direct fit.. Sorry, NO .. way too low mate..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...