Jump to content
SAU Community

Recommended Posts

Ok Mohammed ur back on the list as confirmed..will ur girlfriend be comong allong with u too now!! :closedeyes:

as for info on the South East pre-meet i believe all the info is in the thread below:

http://www.skylinesaustralia.com/forums/in...t&p=3408212

...so once again, list updatd

Edited by DNGRUS
  • Replies 131
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

No worries Ilyas, hopefully you and your R33 can make it...

If not pass this message onto Serife for me, tell her Ferah said for her to still come in her integra :)

Hey Ferah yeh sorry bout that, yeh ill pass it on,i might actually give her my car n she can cum with that. If you want give her a call before sunday.

No worries Ilyas, hopefully you and your R33 can make it...

If not pass this message onto Serife for me, tell her Ferah said for her to still come in her integra :)

Hey Ferah yeh sorry bout that, yeh ill pass it on,i might actually give her my car n she can cum with that. If you want give her a call before sunday.

Hahaa ok ill probly see her either 2nyt or 2mro 4 sure @ work...

:)

Thnxx Ilyas

What time is the SE Pre-Meet? Can anyone confirm please. I can't seem to find it in this thread. I know the location, just need time.

Cheers

Moe

pm ashneel he'll give u all the details or check the link out at the top of thispage. fearh posted it up.

What time is the SE Pre-Meet? Can anyone confirm please. I can't seem to find it in this thread. I know the location, just need time.

Cheers

Moe

Hey Moe, here is a quote from Ashneel in regards to the south east preemeet @ Brandon Park

9:15sh and we leave 9:45

:P

ALLURE Girls would like to thank those who attended the ALLURE Mini Meet/ Mini Cruise!

it was a great day a few hick-ups but for our first cruise it went pretty good... Great Weather and a great group of people!

Pics will be posted soon!

Cheers

ALLURE GIRLS

Big Thanks to the Allure Car Club for holding such a great cruise!.

Weather was nice, and there was a decent turnout of cars.

Nice to meet a few new faces, and to let my gtr stretch its legs on those awesome roads.

Trentham Falls was a good stop, especially on a hot day like it was yersterday.

Can't wait for the next one :P

Anywayz.. here are a few snaps i took.

21102007050wk8.jpg

21102007051de3.jpg

21102007052dj2.jpg

21102007060bn8.jpg

21102007057gw1.jpg

21102007046il7.jpg

21102007059gz9.jpg

21102007058md7.jpg

21102007056vd7.jpg

21102007047rz6.jpg

im glad u all enjoyed it..!

I know i did! Everyone who came, THANK U! You were all so freindly and was a GREAT pleasure to meet u all..!

Will see u all at the next event and hope to cruise with u all soon

-Ferah

(oh btw - ill have my piks up hopefully 2mro!)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...