Jump to content
SAU Community

Recommended Posts

Hey guys, at the moment im using the aerial cable as my earth for headunit, but now i want to use my aerial so where is the best nice and easy spot for new earth? I also want to run some of my guages to this earth also, Any ideas? Its for a R33 S2.

I have tried a couple spots around the bolts by the gearbox etc, no luck.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/188310-want-a-new-earth-for-headunit/
Share on other sites

Times three!

I sanded the metal ring part (after removal. Easy), stuck a bolt and washer over one hole, then sprayed the whole thing black gloss. Remove the bolt and washer, and you have a perfectly clean grounding point. Attach ground wire after re-installing it all and then spray or rub with some kind of lubricant (WD40, etc), which will stop the bare metal from rusting.

I tried the spot u three guys use, tested it with light n was ok the connected it up properly n for sum reason didnt work? I still duno y it didnt work.

Just to make sure we are talking about the same spot, one of the four bolts underneath the gearstick cover, beside the lower rubber part off stick?

make sure youve sanded back any paint that is at that point. bare metal is a good ground, paint is not :) by all means paint over it once grounded to stop rust. also make sure the ground wire from the head unit isnt dodgy. ive had one with a break in the ground wire before. would work randomly. replaced the ground wire at the plug - which wasnt fun :(

wire is all fine, dont think its an fuse problem as when i change back to my old earth it all good. Im really confused why when i test the point steve told me it shows its good, then I wire it up, none of the bolts can be earthed when i test with light. Its fine till i connected it lol. Then i take it off and that point is ok again :thumbsup:

I tried the spot u three guys use, tested it with light n was ok the connected it up properly n for sum reason didnt work? I still duno y it didnt work.

Just to make sure we are talking about the same spot, one of the four bolts underneath the gearstick cover, beside the lower rubber part off stick?

That quiet funny actually, because I wired up a head unit in my friends R32, and used the same grounding point as mine, which is the one were all referring too, and it didn't work either!

Very weird..

I just used one of the other screw holes that holds the rubber boot thing in place.

The mounting bracktes in the dash, to the left and right side of the head unit also work as an earth.

So i can use the earth point at the back of head unit then if i can earth to mounting brackets? I havent had a good look at it but i thought the brackets are all attached to plastic and not the body at all?

Yer... I probably wouldn't trust the brackets to be well grounded actually.

Failing the rubber boot surround bit, perhaps go for something around your handbrake? Removing the entire centre console at the point you are now is just a few extra screws.

Yea i had all that off aswell fitting switches in my console box. Il have a play around the handbreak in the weekend, I did try what Hellfire said at start but i had trouble geting dam footrest off, is there more than just 2 screws or what?

Also what is that thing underneath the console box? behind the handbreak a lil bit. Is that something to do with the airbags?

Oh i see, yea i took the front 2 off and couldnt get the footrest off so i tried hookin earthcable up to one of them bolts lol no gud, how does the foot rest come off? i used a bit of force but also didnt wana break it lol im gud at that haha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...