Jump to content
SAU Community

Recommended Posts

i'm sure the safc2 has more load points then the safc and also has the option for two maps to be saved. the safc2 also has a knock reading feature that the safc doesn't.

Is there where i can go to Find out

cause all i can see the difference is the look of it

Link to comment
https://www.sau.com.au/forums/topic/189249-safc-v-safc-ii/#findComment-3410806
Share on other sites

Is there where i can go to Find out

cause all i can see the difference is the look of it

i've used both of them and from what i can remember the safc only has 8 load points at 500rpm intervals and the safcII has 12 load points at 200rpm intervals. and also the knock signal readout and the option for 2 maps on the safcII.

if you want more detailed info you might be able to try the apexi site?

Link to comment
https://www.sau.com.au/forums/topic/189249-safc-v-safc-ii/#findComment-3410836
Share on other sites

i've used both of them and from what i can remember the safc only has 8 load points at 500rpm intervals and the safcII has 12 load points at 200rpm intervals. and also the knock signal readout and the option for 2 maps on the safcII.

if you want more detailed info you might be able to try the apexi site?

I just got a SAFC blue screen for $150 would that do the job

or should i get the Safc 2

Edited by charlie25T
Link to comment
https://www.sau.com.au/forums/topic/189249-safc-v-safc-ii/#findComment-3410841
Share on other sites

safc is fine. the safcII would just give you a few more tuning points. for what the safc is though you probably wont need them, it all depends on your setup. i haven't seen any one yet use the option to run two maps. the knock sensor readout is ok to have but i don't think it is that accurate.

Link to comment
https://www.sau.com.au/forums/topic/189249-safc-v-safc-ii/#findComment-3410869
Share on other sites

safc is fine. the safcII would just give you a few more tuning points. for what the safc is though you probably wont need them, it all depends on your setup. i haven't seen any one yet use the option to run two maps. the knock sensor readout is ok to have but i don't think it is that accurate.

i have a R33 with basic mods

FMIC, POD WITH COLD AIR

DUAL STAGE BOOST CONTROLLER 12PSI ON SWITCH

ATMO BOV

Link to comment
https://www.sau.com.au/forums/topic/189249-safc-v-safc-ii/#findComment-3410872
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...