Jump to content
SAU Community

Vortech's owner in troub, need urgent help: Where can you get an emission test in SA?


Recommended Posts

A friend of mine is getting a Vortech SC kit for his car. He checked with registration who then referred him to Regency. :P

Regency requested a emission test result to be able to register the car!!!!! He has been quoted $4000 for the test in SA ;)

The kit on this car is exempted from emission control everywhere in the world. The kit has a placard attached to the supercharger stating so. The car is only 3 years old and set the world record for the lowest emission engine/exhaust system. Regency still would not register this car unless it has the test done in Australia.

What the hell is going on with the government? What is the fairness here? Does every car need a emission test if something is done to the car? Does LPG car need a emission test when LPG get installed?

Do you guys know of any other ways around this problem?

Could you guys tell me where Regency is and who work there?

What car is it for?? I would suggest calling them, as most of the common kits have been EPA tested... Also speak with Tonkin and associates in Adelaide.. They are consulting engineers that i think do the testing for CAPA.. All you need to do, it the emmssions has been done on the kit by CAPA is to pass a noise test.. Not much at all $$$$...

Originally posted by SR910

A full drive cycle emissions test at mitsubishi motors is just upwards for $4,000.

Yes, this is what my friend told me too.

Is there any other place that carry out the test as well? Doe Holden in Elizabeth do this test?

I would just ring CAPA, as i had to go through this with my Powerdyne kit when i lived W.A. All you have to do is a noise test.. As the kit for the 5.0L is already Emmissions compliant..

What Vortech do you have Is it the V2 (silent Vortech) as the normal V-1 S Trim may not pass..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...