Jump to content
SAU Community

Need Small Help

guricha

By guricha,
in Engines & Forced Induction

 Share

Recommended Posts

guricha Collaborator

guricha

Posted
Posted (edited)

two days ago finaly i got my turbo and install it on my GTSt R33, car working propertly and runing wel but have problem knock sensor shows up 25 knock sometimes and please be kind and sugest can i proceed to drive car or need to tune FC? actualy tune FC is main problem here nowbody knows how to tune it right... and i havenot change spork plug yet seems itsnot changed many years...

and is there any post or any information where i can lern how tu tune FC?

thanks in advanced

Edited by guricha
Link to comment
https://www.sau.com.au/forums/topic/197681-need-small-help/
Share on other sites
guricha Collaborator

guricha

Posted
  • Author
Posted (edited)

guys Is someone using KKR480 ? and when it boosting up?? on my car its going on full boost on 4800 RPM is it normal??

and who knows how to tesy car on dyno please gice some advice, on which gear need to run up and on which RPM, because In tbilisi (I am from Georgia) we dont have dyno yet and because i bought utility whichcalculate HP on GPS system, but i dont know in which second or third gear and in which rpm i need to test it my turbo boosts up on 4800 RPM

thanks in advanced

Edited by guricha
Link to comment
https://www.sau.com.au/forums/topic/197681-need-small-help/#findComment-3540230
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Things are happening.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • Pac
      The New Official S A U - N S W Spotted Thread

      By Pac · Posted

      I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • Komdotkom
      NC MX5

      By Komdotkom · Posted

      The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...