Jump to content
SAU Community

Recommended Posts

Do you know anything about auto leveling and washers on the front, you see I have HID's and got a yellow went to the pits and they told me HID's have to be auto lvl and washers on the front otherwise they have to be put back to stock..... does anybody know if this is true...

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3550139
Share on other sites

Well i know that luxury cars that come out with HIDs from factory have those washers to clean the headlights, so probably is true.

Why not just replace the stock ones back and go through pits, then install the HIDs again? I did that when i got yellowed.

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3550557
Share on other sites

  • 2 weeks later...

i've been selling H.I.D. for few years and lots of members here know me as well.

there's no H.I.D. legal without autoleveling, self washer, and projector lense.

who ever sell h.i.d.and tell you that hid under 6000 is legal is just try to cheat you and missleading the understanding of the law.

no aftermarket hid is legal.

HOWEVER

never heard anyone got pulled over and got yellow sticker only because of the h.i.d.

also, if you hide the ballasts well, you can go over the pits with no problem, coz when they check the car is daytime and thy wouldn't tell the defference.

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3561723
Share on other sites

Thats all well and good bankids but its on the sheet that have to remove them so now im at point now where I have to change it back over, But thankyou about the info about the auto lvl and washers at least now I know the guy wasnt full of it

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3561927
Share on other sites

Probably a stupid question but why are hid lights illegal to install on cars that didnt come with them? If there a better light wouldnt they be better to use?

because as bankids mention your car needs to have the following...

there's no H.I.D. legal without autoleveling, self washer, and projector lense.
Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3562286
Share on other sites

Probably a stupid question but why are hid lights illegal to install on cars that didnt come with them? If there a better light wouldnt they be better to use?

Because HID's are a lot brighter than standard lights and emit a different kind of light, and because of this the light is not controlled and adjusted correctly. So when somebody comes driving down the road in the oposite direction to you, they can see sweet f**k all because you've essentially got high-beams blaring into their eyes.

That's why you need the washer, projector and auto leveling because these three things stop the HID light going astray and blinding the crap out of everybody else on the road.

I'm quite interested in replacing my high beams with a cheap HID kit, becuase they're high beams so I dont really think it matters (from a moral stand point) if they are blinding and point up too hight (compared to standard beams). I know they'll still be illigal but I wont feel bad and they wont be blinding eveybody. Plus it makes my country driving that little bit more safe. :down:

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3562442
Share on other sites

Because HID's are a lot brighter than standard lights and emit a different kind of light, and because of this the light is not controlled and adjusted correctly. So when somebody comes driving down the road in the oposite direction to you, they can see sweet f**k all because you've essentially got high-beams blaring into their eyes.

That's why you need the washer, projector and auto leveling because these three things stop the HID light going astray and blinding the crap out of everybody else on the road.

I'm quite interested in replacing my high beams with a cheap HID kit, becuase they're high beams so I dont really think it matters (from a moral stand point) if they are blinding and point up too hight (compared to standard beams). I know they'll still be illigal but I wont feel bad and they wont be blinding eveybody. Plus it makes my country driving that little bit more safe. :P

When u pick the colour for your high beam, don't use any colur over 5000k as they don't work good on high beam, i have 10000k hid kit in my high beam 8000k in foglights and 4300k in lowbeam, when i did some country road i felt the high beam doesn't really work.

also when u want to buy some cheap ones that's ok just buy from local shop who do replacement inside of australia. at least when u want your warranty u can still find them.

my 2 cents

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3566047
Share on other sites

I'm quite interested in replacing my high beams with a cheap HID kit, becuase they're high beams so I dont really think it matters (from a moral stand point) if they are blinding and point up too hight (compared to standard beams). I know they'll still be illigal but I wont feel bad and they wont be blinding eveybody. Plus it makes my country driving that little bit more safe. :P

Thats a good idea. . putting them into the high beams. Would that work? You would be able to just flick back to low beam when on coming cars are there. I do a fair bit of country driving so some a bright light would be good to have as i dont really want to put spotties on the fromt of my supra

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3566156
Share on other sites

only disadvantage of put hid to hi beam is when u switch to high beam it's not instantly light up, always being a flash before it lites up. so when u drive country road you gonna watch out. unless ur hi and low beam can be on at the same time..but skyline can't

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3566327
Share on other sites

only disadvantage of put hid to hi beam is when u switch to high beam it's not instantly light up, always being a flash before it lites up. so when u drive country road you gonna watch out. unless ur hi and low beam can be on at the same time..but skyline can't

Unless you re-wire it, another mod I was considering but haven't had the chance to look into. Probably a bit beyond my electronics skill, but I have a few mates who are into that sort of thing and should be able to help me out there.

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3568147
Share on other sites

Unless you re-wire it, another mod I was considering but haven't had the chance to look into. Probably a bit beyond my electronics skill, but I have a few mates who are into that sort of thing and should be able to help me out there.

There is a guide on how to do it somewhere here on SAU... Its quite simple from memory. Try the Tutorial section.

Edit: Here you go... It involves removing the indicator stalk and bridging the gap between two points with solder. Pictures and all, this is about as simple as automotive electronics gets! :rolleyes:

http://www.skylinesaustralia.com/forums/Du...html&st=40#

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3576265
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...