Jump to content
SAU Community

Recommended Posts

Do you know anything about auto leveling and washers on the front, you see I have HID's and got a yellow went to the pits and they told me HID's have to be auto lvl and washers on the front otherwise they have to be put back to stock..... does anybody know if this is true...

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3550139
Share on other sites

Well i know that luxury cars that come out with HIDs from factory have those washers to clean the headlights, so probably is true.

Why not just replace the stock ones back and go through pits, then install the HIDs again? I did that when i got yellowed.

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3550557
Share on other sites

  • 2 weeks later...

i've been selling H.I.D. for few years and lots of members here know me as well.

there's no H.I.D. legal without autoleveling, self washer, and projector lense.

who ever sell h.i.d.and tell you that hid under 6000 is legal is just try to cheat you and missleading the understanding of the law.

no aftermarket hid is legal.

HOWEVER

never heard anyone got pulled over and got yellow sticker only because of the h.i.d.

also, if you hide the ballasts well, you can go over the pits with no problem, coz when they check the car is daytime and thy wouldn't tell the defference.

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3561723
Share on other sites

Thats all well and good bankids but its on the sheet that have to remove them so now im at point now where I have to change it back over, But thankyou about the info about the auto lvl and washers at least now I know the guy wasnt full of it

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3561927
Share on other sites

Probably a stupid question but why are hid lights illegal to install on cars that didnt come with them? If there a better light wouldnt they be better to use?

because as bankids mention your car needs to have the following...

there's no H.I.D. legal without autoleveling, self washer, and projector lense.
Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3562286
Share on other sites

Probably a stupid question but why are hid lights illegal to install on cars that didnt come with them? If there a better light wouldnt they be better to use?

Because HID's are a lot brighter than standard lights and emit a different kind of light, and because of this the light is not controlled and adjusted correctly. So when somebody comes driving down the road in the oposite direction to you, they can see sweet f**k all because you've essentially got high-beams blaring into their eyes.

That's why you need the washer, projector and auto leveling because these three things stop the HID light going astray and blinding the crap out of everybody else on the road.

I'm quite interested in replacing my high beams with a cheap HID kit, becuase they're high beams so I dont really think it matters (from a moral stand point) if they are blinding and point up too hight (compared to standard beams). I know they'll still be illigal but I wont feel bad and they wont be blinding eveybody. Plus it makes my country driving that little bit more safe. :down:

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3562442
Share on other sites

Because HID's are a lot brighter than standard lights and emit a different kind of light, and because of this the light is not controlled and adjusted correctly. So when somebody comes driving down the road in the oposite direction to you, they can see sweet f**k all because you've essentially got high-beams blaring into their eyes.

That's why you need the washer, projector and auto leveling because these three things stop the HID light going astray and blinding the crap out of everybody else on the road.

I'm quite interested in replacing my high beams with a cheap HID kit, becuase they're high beams so I dont really think it matters (from a moral stand point) if they are blinding and point up too hight (compared to standard beams). I know they'll still be illigal but I wont feel bad and they wont be blinding eveybody. Plus it makes my country driving that little bit more safe. :P

When u pick the colour for your high beam, don't use any colur over 5000k as they don't work good on high beam, i have 10000k hid kit in my high beam 8000k in foglights and 4300k in lowbeam, when i did some country road i felt the high beam doesn't really work.

also when u want to buy some cheap ones that's ok just buy from local shop who do replacement inside of australia. at least when u want your warranty u can still find them.

my 2 cents

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3566047
Share on other sites

I'm quite interested in replacing my high beams with a cheap HID kit, becuase they're high beams so I dont really think it matters (from a moral stand point) if they are blinding and point up too hight (compared to standard beams). I know they'll still be illigal but I wont feel bad and they wont be blinding eveybody. Plus it makes my country driving that little bit more safe. :P

Thats a good idea. . putting them into the high beams. Would that work? You would be able to just flick back to low beam when on coming cars are there. I do a fair bit of country driving so some a bright light would be good to have as i dont really want to put spotties on the fromt of my supra

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3566156
Share on other sites

only disadvantage of put hid to hi beam is when u switch to high beam it's not instantly light up, always being a flash before it lites up. so when u drive country road you gonna watch out. unless ur hi and low beam can be on at the same time..but skyline can't

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3566327
Share on other sites

only disadvantage of put hid to hi beam is when u switch to high beam it's not instantly light up, always being a flash before it lites up. so when u drive country road you gonna watch out. unless ur hi and low beam can be on at the same time..but skyline can't

Unless you re-wire it, another mod I was considering but haven't had the chance to look into. Probably a bit beyond my electronics skill, but I have a few mates who are into that sort of thing and should be able to help me out there.

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3568147
Share on other sites

Unless you re-wire it, another mod I was considering but haven't had the chance to look into. Probably a bit beyond my electronics skill, but I have a few mates who are into that sort of thing and should be able to help me out there.

There is a guide on how to do it somewhere here on SAU... Its quite simple from memory. Try the Tutorial section.

Edit: Here you go... It involves removing the indicator stalk and bridging the gap between two points with solder. Pictures and all, this is about as simple as automotive electronics gets! :rolleyes:

http://www.skylinesaustralia.com/forums/Du...html&st=40#

Link to comment
https://www.sau.com.au/forums/topic/198973-hids/#findComment-3576265
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...