Jump to content
SAU Community

What Size Boost Jets Do I Need To Run

R33GOD

By R33GOD,
in Engines & Forced Induction

 Share

Recommended Posts

MANWHORE Grand Master

MANWHORE

Posted
Posted
forget the term boost jet and call it what it actually is. A "Restrictor"

its a small piece of steel tube that is fittted snuggly inside the actuator supply line from the manifold.

it has a smaller hole in the middle approx 2.5 - 3mm compared to the 6mm rubber line.

im running one in conjunction with my PFCBC and a 18psi actuator and i have no issues controlling boost up to 27psi.

ramps onto boost hard, and then stays within 1psi to redline.

and just to clarify an earlier remark in regards to increasing boost can make it come on sooner.

if your target level is close or just past your actuator tension, then your internal gate flap will allready be opening before you reach your target boost as to control the clime in pressure. If you were to run a heavier actuator and run higher boost then the flap will stay completely shut for longer causing it to ramp up harder and earlier.

not 1000rpm sooner but certainly 100 - 300rpm sooner.

What I do is I start with a brass t piece. Solder the third leg closed. Then I use my micro drill bits used for drilling electronics like printed circuit boards. I just start drilling bigger until I get the right boost. Either that, or start big and solder it and go smaller.

soldering the brass is very easy. that way you don't have to keep buying nozels.

the t piece costs like $2.

MANWHORE Grand Master

MANWHORE

Posted
Posted

It works without an aftermarket ecu. Just get rid of the stock solenoid.

Either that, or get a jaycar iebc and use it to control the solenoid (and use a restrictor to control the boost level).

The jaycar iebc will allow you to have the quickest possible boost build and best control over the boost curve compared to any ebc out there.

dangerman4 Mentor

dangerman4

Posted
Posted
my gtr runs a Tee'd off little peice of silicone hose with a utilux bullet head clamped inside with a hole in the end. 13 psi.

Now thats a cheap ass controller!

"Clamped" Huh

look like zip ties to me.

back yard racing FTW.. lol

mine is an internal restricor inside the feed line. i dont have a T peice.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...