Jump to content
SAU Community

Recommended Posts

Make / Model / Year: 1987 HR31 Skyline GTS Coupe

Location: Ipswich QLD

Kilometers: 74,400

Transmission type: 5sp manual

Engine: RB20DET (160kw atw)

Colour: White

Modifications:

4300K HID’s (low beam)

RB25 T3 turbo

Walbro 500hp fuel pump

Chipped ECU (with switch for speed/rev cut)

Apexi pod filter

GTS-R strut brace

Greddy Profec B Spec II boost controller

Genuine Hybrid FMIC

Custom 2 core radiator

Custom turbo back 3” exhaust

Turbosmart type 3 plumback BOV

RB25 clutch fan and hub

Viper alarm with remote start

JIC coilovers (height, damper and camber adjustable)

17” Performance rims

Darkest legal tint (proper M3 metallic tint)

Electronic water temp gauge

Autotechnia steering wheel

JVC head unit with 6” Kicker speakers front and 6x9 Kicker speakers rear running off a 4x80w amp.

Roadworthy Certificate: Supplied upon sale

Registered: yes, 10/06/2008

Accident History: None

Asking Price: $10,000

Contact Details: Please PM for further information

Other Comments: Owned for the past 4 years, first owner in Australia, genuine no smoker, weekend use only (9,000k‘s a year), well maintained and serviced every 4,000k’s with Castrol Edge 10w60 along with changing plugs and filter. Had major service 8000k’s ago and replaced (genuine Nissan parts) the timing belt, tensioner and idler bearings, water pump, replaced gear box and diff oil with top of the range Castrol oil. All modification were carried out in Australia, car was 100% standard when purchased.

Backyard_2.jpg

Backyard_1.jpg

DSC_0076_800.jpg

DSC00002-2.jpg

DSC00006-1.jpg

0091.jpg

dyno_31.jpg

Edited by HR31_RB20DET
Link to comment
https://www.sau.com.au/forums/topic/200665-fs-hr31-gts-coupe/
Share on other sites

I can vouch that this would definately have to be one of the neatest and tidiest R31 coupes around, with genuine low k's. Very nice to drive too.

LOL i still remember when you bought this with the stocko hubcaps on it!!!

Hope the new owner will take as good care of it as you have over the past few years!

Thanks, the stock hub caps were exquisite :D

This is the car just before I purchased it and before a lot of time and money went into it.

GTS1.jpg

GTS2.jpg

Edited by HR31_RB20DET
  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...