Jump to content
SAU Community

Recommended Posts

Hey guys i got few things forsale, they were off a vl turbo tho you could use on a skyline or differnt car alltogether if you wanted to so i figured i'd post it up here and see if any interest.

Turbonetics t60 with 60mm comp wheel, just been totally rebuilt by precision not used yet! good for 300rwkw (please take note that this is not a donkey turbo you buy from china this is from the usa and built by a good company which has been around 29years.)

Standard VL turbo manifold slightly ported with welded adapter plate for external waste gate

44mm Tial external wastegate with screamer pipe

Also comes with Oil Lines

This setup has produced 258rwkw on 16psi though a auto gearbox $1500 SOLD

0000088ry2.th.jpg

0000087bh6.th.jpg

0000083fp9.th.jpg

----------------------------------------------------------------------------------------------------

6 seimens 550cc injectors in perfect running order items were hardly used

Only done 1000 k's $500 SOLD

0000089wd5.th.jpg

----------------------------------------------------------------------------------------------------

everything has sold please delete this thread thx.

Edited by revenge_of_the_trader
Link to comment
https://www.sau.com.au/forums/topic/202225-sold/
Share on other sites

Hey mate, how much u want for the turbo?? and does it come with everything i need eg: hosing

hey buddy $900 for turbo, it comes with the hose and oil line

heres a pic of the items which come with the turbo/ turbo setup

1000020sm2.th.jpg

Link to comment
https://www.sau.com.au/forums/topic/202225-sold/#findComment-3596944
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...