Jump to content
SAU Community

R32/33 Exedy Heavy Duty Clutch Kit

R32_Matt
 Share

Recommended Posts

R32_Matt Rising Star

R32_Matt

Posted
Posted

Item: Exedy heavy duty clutch kit

Age: Approx 1 year

Condition: Good

Price: $200 ono + postage

To Fit: R32/33 GTST

Location: ACT

Contact: PM or call Matt on 0400 440 932

Comments:

Exedy heavy duty clutch kit.

Comes with clutch plate, pressure plate and a brand new thrust bearing.

Clutch plate and pressure plate have done approx 4000k's.

Clutch plate still has plenty of meat on it.

Will fit both R32 and R33 GTS-T models so rb20 and 25 turbo.

May also fit non turbo models but i am not sure of this.

Also fits VL commodore.

price is $200 but it is negotiable.

Postage extra

Pm or call Matt on 0400 440 932

Link to comment
https://www.sau.com.au/forums/topic/204928-r3233-exedy-heavy-duty-clutch-kit/
Share on other sites
tootooldrifter Explorer

tootooldrifter

Posted
Posted (edited)

were in canberra are you located going across this after noon to pick up a motor? give me you lowest price and it will be gone

Edited by tootooldrifter

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...