Jump to content
SAU Community

Recommended Posts

Autotech now has Nistune stock ecu chip burning software, behaves exactly like a PFC except a programmable chip gets soldered into the ecu in place of the original before tuning. Unfortunately not fully for R33GTSt - -some restrictions - but just about everything else Nissan with an ecu.

Edited by Scooby
Autotech now has Nistune stock ecu chip burning software, behaves exactly like a PFC except a programmable chip gets soldered into the ecu in place of the original before tuning. Unfortunately not for R33GTSt but just about everything else Nissan with an ecu.

RE HEH HEH HEH HEH HEH HEEEEEEEALLLLLYYYYY???????

My constant hints to Pete came to fruition, he confirmed today that they have a dealer license. Current price is $220AUD for board, $200AUD NIStune Software (Individual Users License) and documentation set. Additionally, shipping and transaction fees may apply.

Then its just the cost of the tune.

Looks like RB25 is supported but not with VCT. Check out the Nistune site, pretty much explains eveything. http://home.aanet.com.au/nistune/

Cheers

Edited by Scooby

Well, my tune was done yesterday and I am very happy... Even though I didnt get much more power from it as we have reached the limits of the turbo and AFM, the boost response, mid range torque, fuel consumption and overall driveability have improved.

This tune was more about getting the engine to run spot on so that I wouldnt have any drama's with pinging while on the track.

9 / 10 for John and Angelo at Trojan - Power FC RB25DET Dyno tune, great tune, right price and anything small and incidental that needed doing (such as rubber grommets / hoses) was done at no extra charge... Very happy.

Pic attached: - Check out that awesome power curve!! :thumbsup:

post-17958-1203645354_thumb.jpg

Fair enough, but I think you'll find that it makes at the very least 1,350hp at the wheels, with still more to go.

Anyway's you should bring the beast to the dyno day I'm sure we would all be interested in seeing and hearing how she goes.

I know this car very well as my friend had a hand in it. It makes 1350 at the flywheel and revs to almost 13000 revs. It does make good power but will not make much more as they are already on the biggest turbo setup and as you can see by the revs massive cams.

Would love to come to the dyno day but unfortunately due to a well known machinist have had to pull it back down again due to valve float issues.

Will be at the next one as have changed machinist's and instead of work taking 8mths it is now almost all completed.

As for the torque mine makes 650lb at 2psi and peaks at 2266lb at 28psi in fourth gear pulls or in nm it makes over 10000nm it makes 2psi by 2800 and full boost by about 5000

As for tunes i would be takin it directly to Jake as i was speakin to him recently and he does alot of tunes on skylines and said he does all the tuning on his dyno.

May save some money

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...