Jump to content
SAU Community

Recommended Posts

Hi guys,

As some of you are aware, i'm in the motion of producing a billet girdle for the rb's. The first one is designed for the 4wd rb30 guys, but i have the capacity to get them made for any rb engine.

What i need to find out is what kind of interest there would be for such an item. There are 2 options, the latter would be the better option, but the first one i have one going in a track car very shortly, so we'll see how that one works.

a) 2 piece billet girdle - The girdle incorporates the sump adapter for the 4wd rb30 conversion. It has a step down to fit to the std cradle (which the main caps are machined to fit)

b) 1 piece billet girdle - The girdle again incorporates the sump adapter for the 4wd rb30 conversion. It is a single unit and replaces the entire std cradle. The bearings are fitted to this new girdle.

The pics below are of the 2 piece option. I'm currently working on the 1 piece girdle, however it wont be ready for some time.

Pricing for these arent cheap, i'll be making 2 parts of stuff all ontop also. 2 piece is around the $2000 mark (including everything needed to bolt it on). 1 piece is around the $3000 mark, pricing for the 1 piece isnt definate yet.

One thought i have had, is to offer the girdle with a machined block/crank to suit. That way eliminating any form of machining error, done in the one place to exact specifications.

I welcome your thoughts and opinions.

cheers

Shane

girdle004rb4.th.jpggirdle005gt2.th.jpggirdle006fs4.th.jpggirdle007aq6.th.jpggirdle008bq9.th.jpg

As someone who's doing the RB30 currently, to be honest, i would say no mainly due to the price but also the fact that AFAIK there's nothing really wrong with the normal one, and plenty of RB30's are doing very well without one :rofl:

It looks stunning though!

As someone who's doing the RB30 currently, to be honest, i would say no mainly due to the price but also the fact that AFAIK there's nothing really wrong with the normal one, and plenty of RB30's are doing very well without one :rofl:

It looks stunning though!

cheers for the comments. i thought that would be the case. but someone had to come up with an available one

at what point would you upgrade to one of these?

tbh you prolly wouldnt bother with anything below 750hp and 7500rpm. although any extra block/bottom end strength must be seen as a plus.

as N1GTR said though, there are rb30's out there doing fine, then there are ones that arent

send it OS get the price realistic and i reckon you would sell quite a few. Target price needs to be $999

(it would be nice to see it without the adapter also, for generic use) would the engine need to be lifted to accomodate for extra thickness between sump and block? i know my sump sits within 3-4mm of the xmemeber.

send it OS get the price realistic and i reckon you would sell quite a few. Target price needs to be $999

(it would be nice to see it without the adapter also, for generic use) would the engine need to be lifted to accomodate for extra thickness between sump and block? i know my sump sits within 3-4mm of the xmemeber.

thats a great idea but where in the world would i find a contact for that? if you have any idea i'm willing to talk...

making them without the added adapter is a piece of piss, its just a 2min model change :)

the below pics are of my 26/30 with my 10mm adapter plate (32gtr), as u can see theres about 4mm clearance (sry for pic size, my nets capped :))

Diff2.jpg

Diff.jpg

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...