Jump to content
SAU Community

Recommended Posts

$600 is way too much

Get them and take them into a local panel shop, be realy nice to the guys in there and just say to one of the guys working that you will give him personally (not the shop, but the worker) $300 if he paints your covers in JWO after hours and there's no rush on the job

$600 is way too much

Get them and take them into a local panel shop, be realy nice to the guys in there and just say to one of the guys working that you will give him personally (not the shop, but the worker) $300 if he paints your covers in JWO after hours and there's no rush on the job

I agree, $600 is way too much and N1GTR has the right idea about approaching a painter in your local panel shop. For $600 you're probably still getting used covers that are just repainted. In korea I can get my RB26 covers painted at a panel shop for ~$250 USD so I'm sure you can get it for about the same in Aus. It's expensive in japan to buy newly painted covers.

Prices for Nissan OEM Painted brand new covers from Japan...

Black

Rocker cover EX side $219 USD

Rocker cover IN side $219 USD

Rocker Ornament cover $263 USD

Front cam pulley cover $315 USD

Red

Rocker cover EX side $210 USD

Rocker cover IN side $210 USD

Rocker ornament cover $242 USD

Front cam pulley cover $125 USD

Gold

Rocker cover EX side $305 USD

Rocker cover IN side $305 USD

Rocker ornament cover ???

Front cam pulley cover $181 USD

I would expect JWO to be more expensive... just to give you an idea.

Edited by chak8080

Go and see Mick at Micolour, He has done plenty.

And well priced too.

I THINK its around $110ish a piece to paint maybe a touch more, you would have to check with mick.

And he is able to remove them off the car and reinstall if required,

although taking in just the pieces is easyer

Edited by vsute
Go and see Mick at Micolour, He has done plenty.

And well priced too.

I THINK its around $110ish a piece to paint maybe a touch more, you would have to check with mick.

And he is able to remove them off the car and reinstall if required,

although taking in just the pieces is easyer

yeah sounds good

ill give them a call tomorrow

or i might even visit them to see what they can do about my scratch on the side of my car too! :D

Go and see Mick at Micolour, He has done plenty.

And well priced too.

I THINK its around $110ish a piece to paint maybe a touch more, you would have to check with mick.

And he is able to remove them off the car and reinstall if required,

although taking in just the pieces is easyer

ouch $550 for the cover set

not much choice really if mil jade is required.

yep i mentioned that before

depends on what your doing with the car i guess :rofl:

just when i think of it , its normally about $800 for a 4 piece body kit to get painted .. engine covers are so so so much smaller lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...