Jump to content
SAU Community

Recommended Posts

Item: R32 GTS ECU

Condition: Perfect

Price: $100 including postage within Australia

To Fit: RB20DET or R32 based RB25/30

Comments: Perfect condition R32 ECU, suitable for replacement into a manual GTS or remappable to suit RB25/30

Item: R33 GTR injector resistor pack

Condition: Excellent

Price: $100 including postage within Australia

To Fit: GTR or cars converting to GTR injectors

Comments: Injector resistor pack suitable for replacement into a GTR or a requirement for other cars using GTR injectors.

Item: R32 RB25DE inlet manifold

Condition: Excellent

Price: $100

To Fit: RB25DE engines or R32 based RB25/30 engines.

Comments: Due to different port size, this is the only inlet manifold suitable for R32 RB25DE based RB25/30's. These lower runners are needed for fabricating front facing plenums also. No throttle body.

Item: R32 Instrument cluster + plastic trim (also have half the dashboard if you want)

Condition: Excellent

Price: $50

To Fit: R32 Gts or dash conversion

Comments: I have the cluster, plastic trim (and half the dash) I was going to use in a swap into my Datsun.

All items are in Melbourne with pick up preferred. Postage possible.

Photos can be taken if required, but items are pretty self explanitory.

Edited by drunkenmaster
righto i want the ecu i'll give u 50 tommorrow

Half the asking price? No thanks.

I'm not desperate for the money, so tomorrow or next week doesn't worry me.

Thanks anyway

  • 2 weeks later...
OK, I'll send you a PM now.

All still for sale which is strange with the amount of definite buyers there were.

Also added now is R32 instrument cluster.

  • 2 weeks later...
  • 1 month later...

Item: R33 GTR injector resistor pack

Condition: Excellent

Price: $100 including postage within Australia

To Fit: GTR or cars converting to GTR injectors

Comments: Injector resistor pack suitable for replacement into a GTR or a requirement for other cars using GTR injectors.

hey mate PM me if you still have the injector resistor pack

Q-do you know if 33 to 32GTR's are different?

  • 2 weeks later...
Item: R33 GTR injector resistor pack

Condition: Excellent

Price: $100 including postage within Australia

To Fit: GTR or cars converting to GTR injectors

Comments: Injector resistor pack suitable for replacement into a GTR or a requirement for other cars using GTR injectors.

hey mate PM me if you still have the injector resistor pack

Q-do you know if 33 to 32GTR's are different?

They are the same.

NOTE: GTR R34 fuel injectors added as for sale however I cant edit my top post for some reason.

Item: R34 GTR injectors x6

Condition: Excellent

Price: $350obo including postage within Australia

To Fit: GTR or RB20DET upgrade

Comments: I have had these wrapped up for around 18 months, they look in almost new shape.

Edited by drunkenmaster
They are the same.

NOTE: GTR R34 fuel injectors added as for sale however I cant edit my top post for some reason.

Item: R34 GTR injectors x6

Condition: Excellent

Price: $350obo including postage within Australia

To Fit: GTR or RB20DET upgrade

Comments: I have had these wrapped up for around 18 months, they look in almost new shape.

post-9530-1213503996_thumb.jpg

  • 4 weeks later...

***R32 GTS ECU SOLD***

***GTR INJECTORS SOLD***

***GTR DROPPING RESISTOR SOLD***

Edited by drunkenmaster

R32 cluster and dash photos as requested

171,377km on the odo...although since the R32 used a mechanical speedo drive, I think you could get creative.

post-9530-1215906652_thumb.jpg

post-9530-1215906665_thumb.jpg

You wouldn't happen to have the steering column surrounds by any chance? I need the bits that cover the indicator switch in a 32. Let me know, mate. Much appreciated.

  • 2 months later...
You wouldn't happen to have the steering column surrounds by any chance? I need the bits that cover the indicator switch in a 32. Let me know, mate. Much appreciated.

No, just what's mentioned.

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...