Jump to content
SAU Community

Recommended Posts

hey guys, this only happens on a COLD start, as soon as I start the car i would get a squeaking noise for about 10-15seconds then stop. This ONLY happens on a cold start and sounds like a belt squeaking?

This 2nd problem is not related to the 1st. The problem is that i get low idles sometimes, looks to be about 550rpm, I beleive the correct idle range is 700rpm, and at other times i would get HIGH idles, around 1500-2000rpm, this dosen't happen ALL the time but does occasionally. Also Sometimes when i start the car, (dosen't happen on cold starts), the idle would seem to want to die but kick itself up then become stable. I read somewhere this COULD be from a split vacuum hose? but i am unsure.

Any pointers guys?

I drive an NA r33 gts4

Link to comment
https://www.sau.com.au/forums/topic/208883-sqeaking-on-start-up-low-idle/
Share on other sites

The hunting is normal. The limits might be a bit extreme which means as above, clean your AAC and maybe even your AFM - use electrical contact cleaner for AFM and carby cleaner for AAC. Check for any air leaks with hot soapy water through any vaccum hoses

That noise is definately your belt. tighten it, spray on crc, or replace it (do others at same time)

Edited by Jmaac

Has anyone actually solved the cold start problems (low idle, having to stab the throttle to start in the worst case, high pitch sqeals) in skylines. I did a quick search and found heaps of threads on this, everyone says to clean the AFM and AAC but this does not cure it

i actually get a similar 'cold start ' effect when i havent fired her up for a good 3 days or more. When i first crank it over, revs will bog down under 300rpm for a split second or two and will then hunt its way up and up. I dont reckon its too much of an issue Matt, unless your car actually dies (on repeated occasions) if you dont stab the accelerator.

I did also have the squeeling belt problem too; tightening the belt up did get rid of the problem. That squeeling doesnt sound too nice ay!

The sqealing was horrible, mine only did it when I would crank it over too long trying to cold start smoother, I had a belt replaced recently which was fitted a touch too tight so thats all fixed.

The skyline cold start issue has gone on forever, personally, I have to give it throttle otherwise it catches and splutters between 0-500rpm and will never rev up but yeah it isn't much of an issue

1st problem

I have this same issue with my car

But, mine just had a major major service done and now starts to do it

So im suspect the belts are a bit loose,

they were all replaced and now are new!

but yeah i think i need to take it in to have them tightened up

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...