Jump to content
SAU Community

Recommended Posts

Well my 33 has been sold for a little while now and while cleaning out the garage I found these.

Stock steering wheel, really good nick just needs a clean $20 SOLD

GENUINE skyline 5 piece floor mats, all in gond condition, driver side one a bit more worn then the rest, good steam clean an they'd be sweet $50 SOLD

stock rear bumper, white, suit resparay as paint's cracked in a few spots an minor scuff marks $30 (I have more pics of this if needed)

stock cat converter, good nick when i pulled it out, perfect for clearing defects, or gutting out ( for track days :thumbsup: ) $30

ALL PARTS FROM R33 GTS-T

Parts are located in Geelong, Victoria. I'm happy to sort out postage at buyers cost if required, bumper would have to be through a courier I'd think?

Cheers

Berin

[email protected]

0417 546 384

post-7879-1206358504_thumb.jpg

post-7879-1206358602_thumb.jpg

post-7879-1206358726_thumb.jpg

post-7879-1206358822_thumb.jpg

post-7879-1206358955_thumb.jpg

Shame your so far away, I am after a good condition rear bar. I am in the eastern suburbs. Are you ever over this way at all, or even up near Brooklyn much and have someway of getting it here. It's too far to come and unfortunately I am never over that way and would hate to think what a courier would charge rofl.

Let me know if ya up this way as some stages

I'm never really up that way at all sorry, an yeah couriers do tend to charge at lot, id guess round $50 for postage.

If its still for sale in a few weeks it'll going to the tip cause im sick of moving it round my garage...lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...