Jump to content
SAU Community

Recommended Posts

UP for sale or swap is my RX7

FOR SALE / SWAP : FC RX7 WITH 300 + RWKW

Engine & Exhaust

13B Bridge Port Turbo, Series 5 Block, Freshly Rebuilt with new SCR 2mm unbreakable seals less than 3500km ago, (its still in run in tune) Solid corner seals, all gaskets and oil seals have been replaced, dowelled, window bearings and stationary gear have been modified to suit, custom made exhaust manifold - heat treaded, T70 turbo kit, earls fittings and braided hoses, turbo beanie bag, 60mm external wastegate, custom heat treated 3.5' exhaust from turbo straight through to hks cannon.

custom hks front mount with custom stainless 3' polished piping, greddy style rs blow off valve, all stainless clamps and 3 ply ss performance silicon joiners, custom made alloy cooler hat, custom polished stainless intake pipe with blitz LM mesh pod filter.

Polished upper manifold and water filler neck, brand new engine mounts, twin belt alternator pulley, brand new break master fitted.

Cooling

PWR alloy radiator, spal 16' thermo fan, all new hoses and clamps, brand new water pump.

Engine Managment

Microtec LT10S, Microtec 4 line hand controller, custom wired and mounted in glovebox with individual switches for fuel pump and ignition, 4 BOSCH ignition coils custom mounted in engine bay with 8.8mm topgun leads, custom bracket for hand controller.

Fuel System

Bosch 700hp intank fuel pump with earls fittings and braided hose, sard fuel pressure regulator, 398cc primary injectors, 1600cc secondary injectors, custom fuel rails to suit these injectors, new bosch injector plugs, new bosch fuel filter, New fuel lines

Driveline

6 Puck button extreme motorsport clutch with 1400kg clamping pressure plate, extreme molly lighten flywheel (6kg), standard 5 speed gear box with new oil, very tight LSD.

Suspension

Tein damper adjustable suspension with lowered springs all round, front and rear strut braces.

Body

Fresh respray in Majestic orange, GP sports body kit, series 5 rear tail lights, crystal blue head lights, custom aero mirrors.

Wheels and Tyres

17' Stern 3 piece light jap rims, bridgestone 235/45/r17 teo1's on the front, bridgestone 265/45/r17 te01's on the rear, rear have 25mm bolt on alloy spacers, front have extended wheel studs with 8mm spacers.

Interior

OBX bucket seats, 3 point racing harnesses, speco boost guage, isotta sports steering wheel, blitz alloy gear knob, new power window switches, razo alloy racing pedals, drift handbrake button.

Sound System

Sony Competition Deck, pioneer 4' front splits, 6'5 JBL rear speakers, 650 watt rms monoblock amp, 600 watt rms 4 channel amp, 2 x 12' JBL dual voice coil subs (600watts rms each), DLS wiring and connectors, subs and amps are mounted in custom setup.

Electrical

Battery has been relocated to boot, isolation switch installed also in boot, brand new orbital 750cca battery.

LOCATION : ADELAIDE

ITEM CONDITION : Good

PICTURES : YES

PRICE : $ 17500 ONO NOW $ 16500 !!!!

CONTACT : MATTHEW

mobile number : 0433549430

post-29615-1206406369_thumb.jpg

post-29615-1206406388_thumb.jpg

post-29615-1206406399_thumb.jpg

post-29615-1206406414_thumb.jpg

Edited by stylz7
Link to comment
https://www.sau.com.au/forums/topic/211865-for-sale-swap-fc-rx7-with-300rwkw/
Share on other sites

  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...